New Giveaway - Wort Monster Conical Fermenter!

Home Brew Forums > Home Brewing Beer > DIY Projects > Another pickup tube option - elbow + silicone




Reply
 
LinkBack Thread Tools Display Modes
Old 08-12-2012, 06:35 AM   #1
TimpanogosSlim
Feedback Score: 1 reviews
Recipes 
 
Join Date: Mar 2012
Location: Orem, UT
Posts: 958
Liked 76 Times on 67 Posts
Likes Given: 5

Default Another pickup tube option - elbow + silicone

So tonight i finally drilled a hole in my HLT for one of the weldless kits i bought from bargainfittings ages ago.

I'd seen some posts about how a simple elbow fitting works fine as a pickup tube, so i ordered some with my valves. And then for months i worried about whether i would end up drilling the hole in the kettle slightly too high or slightly too low.

As it turns out i drilled a bit high, about half an inch from the bottom of the elbow to the bottom of the kettle. So i started wondering about what i could install that would give me a siphon closer to the bottom of the kettle.

Turns out that 1/2" ID silicone tubing fits neatly inside 1/2" NPT female threads.

I'll see how it works out tomorrow.



__________________
TimpanogosSlim is offline
 
Reply With Quote Quick reply to this message
Old 08-12-2012, 01:32 PM   #2
BargainFittings
Vendor
HBT_SPONSOR.png
Feedback Score: 1 reviews
 
BargainFittings's Avatar
Recipes 
 
Join Date: Nov 2008
Location: Allen TX
Posts: 1,835
Liked 37 Times on 32 Posts
Likes Given: 3

Default

A hose barb would work and you can angle it down to where you need it.

The tubing might loose suction unless you can get a very tight fit on the inner threads.



BargainFittings is offline
 
Reply With Quote Quick reply to this message
Old 08-12-2012, 05:26 PM   #3
OneHoppyGuy
HBT_SUPPORTER.png
HomeBrewTalk 2012 Vendor Giveaway Participate
Feedback Score: 0 reviews
 
OneHoppyGuy's Avatar
Recipes 
 
Join Date: Nov 2009
Location: Concord, CA
Posts: 1,706
Liked 36 Times on 31 Posts
Likes Given: 52

Default

we used silicone on a customer's keggle to get underneath the pico false bottom

It works great

__________________

Brewright. All Rights Reserved. We reserve the right to brew and to help you brew. To protect the brew and defend the brew. To make the brew and drink the brew.

BrewSteel.com
BrewSteel on Facebook

OneHoppyGuy is offline
 
Reply With Quote Quick reply to this message
Old 08-12-2012, 05:46 PM   #4
TimpanogosSlim
Feedback Score: 1 reviews
Recipes 
 
Join Date: Mar 2012
Location: Orem, UT
Posts: 958
Liked 76 Times on 67 Posts
Likes Given: 5

Default

I guess i should take a picture - I've got the elbow + bit of hose pointing straight down

I'll see if it loses suction during my brew day today. even if it doesn't work out right, it'll be less pouring than I'm used to.

__________________
TimpanogosSlim is offline
 
Reply With Quote Quick reply to this message
Old 08-12-2012, 07:10 PM   #5
TimpanogosSlim
Feedback Score: 1 reviews
Recipes 
 
Join Date: Mar 2012
Location: Orem, UT
Posts: 958
Liked 76 Times on 67 Posts
Likes Given: 5

Default

OK, if draining rinse water out of the kettle counts, and it should, if i tip the kettle to the side when it gets near the last of it, it leaves behind a little less than 1/2c of water.

__________________
TimpanogosSlim is offline
 
Reply With Quote Quick reply to this message
Old 03-04-2013, 02:00 PM   #6
ClemsonDV
Feedback Score: 0 reviews
Recipes 
 
Join Date: Oct 2012
Posts: 46
Liked 1 Times on 1 Posts

Default

Quote:
Originally Posted by TimpanogosSlim View Post
I guess i should take a picture - I've got the elbow + bit of hose pointing straight down

I'll see if it loses suction during my brew day today. even if it doesn't work out right, it'll be less pouring than I'm used to.
How is this working. I bought an 90 deg elbow without the street, and I am starting to worry that i will have the valve up to high. I want to give myself enough room for protecting the valve against heat and also that I can possible get fit in a pickup tube later on.

I was curious to how the silicone tubing is working with it being so close to the bottom and the diect heat. I am slightly worried the burner would affect the tubing because its so close to the bottom of the kettle.

Amazon has some 1/2" NPT pipe threads for cheap that I might use as well. Just not sure what direction to take and I am dying to put my valves in.
__________________
Primary: Black IPA
Kegged: Winter Cheer, Pliny Clone
Bottled: American Pale Ale
Up Next: Centennial Blonde
ClemsonDV is offline
 
Reply With Quote Quick reply to this message
Old 03-04-2013, 03:29 PM   #7
OneHoppyGuy
HBT_SUPPORTER.png
HomeBrewTalk 2012 Vendor Giveaway Participate
Feedback Score: 0 reviews
 
OneHoppyGuy's Avatar
Recipes 
 
Join Date: Nov 2009
Location: Concord, CA
Posts: 1,706
Liked 36 Times on 31 Posts
Likes Given: 52

Default

Check this fitting from BrewHardware.com out



__________________

Brewright. All Rights Reserved. We reserve the right to brew and to help you brew. To protect the brew and defend the brew. To make the brew and drink the brew.

BrewSteel.com
BrewSteel on Facebook

OneHoppyGuy is offline
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options
Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
Filtered pickup tube. kickrjason DIY Projects 3 02-11-2012 02:36 PM
BK Pickup Tube? CorgiBrew DIY Projects 2 05-10-2010 08:11 PM
pickup tube problems MTHarrington DIY Projects 14 11-30-2009 06:07 PM
another pickup tube question Donner DIY Projects 32 04-26-2009 04:04 AM
DIY Wort Pickup Tube from BYO Mag scottfro DIY Projects 24 11-18-2008 05:24 AM