Ss Brewing Technologies Giveaway!

Home Brew Forums > Home Brewing Beer > Beginners Beer Brewing Forum > Transferring brew from fermentation to pressure barrel.
Reply
 
LinkBack Thread Tools
Old 01-02-2014, 09:17 AM   #1
BrettPreston
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2013
Posts: 56
Default Transferring brew from fermentation to pressure barrel.

Hi all. I'm in the process of my first ever brew. Just wanted to ensure I have this process correct and if not what I need to do / change...

So, the beer has been fermentation for around 10 days and seems to of gone well. I'm currently just getting reading and they seem to be the same and consistent each time at 1.012 which is good as recommended on the instructions for this beer is 1.014.

So, once I've done 1/2 more readings to be doubly sure are these steps correct...

Sanitise pressure barrel and other tools and rinse clean.

Using a tube (included in kit) transfer beer into the pressure barrel.

Add sugar. Up to 100g (instructions direct) normal white sugar??

Tighten lid, leave in a warm place for a further 2/3 days.

After this, can it then be put somewhere cooler or cold? As such as the garden for a few weeks? Or will it need to still be indoors but not so warm as before?

Thanks for any help you can give.

__________________
BrettPreston is offline
 
Reply With Quote Quick reply to this message
Old 01-02-2014, 12:05 PM   #2
DocScott
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2012
Location: Rockland County, NY
Posts: 790
Liked 107 Times on 83 Posts

Default

I've never used a pressure barrel before, but from what I can gather, its just like making a huge bottle of beer. Your steps look ok from what I can see. Here's my suggestion.

1. Finish fermenting beer
2. Sanitize anything touching final beer - barrel, tubing, racking cane, spigot
**3. make a priming solution
Boil 1-2 cups of water for a few minutes. Add your desired amount of priming sugar to the boiling water to dissolve and boil for a few minutes.
**4. Add priming solution to barrel
5. Transfer finished beer into barrel
(adding the priming solution helps to ensure even distribution of the sugar into the beer. In the case of a pressure barrel, I think the biggest advantage is to make sure the sugar is dissolved so it doesn't just clump at the bottom)
6. Wait for yeast to digest sugars and make carbonation. This can take anywhere from a few days to a couple of weeks. Warmer conditions will help this occur faster.
7. Chill to serving temps.

I'm going to assume that you are in Europe? In the US, "pressure barrels" aren't widely used, so please, if anyone sees something glaringly wrong, feel free to correct.

I think the other thing to keep in mind is that since this is a closed system used to create carbonation in the beer, you must ensure a good seal on all possible areas where the CO2 could escape (spigot, lid). You may want to use some kind of lubricant/sealant like keg lube to help. Also, be very careful as in theory, depending on how much sugar is used, you can create a lot of pressure inside the barrel. Make sure it can handle the load you're intending to put into it! Congrats on the first brew

__________________
DocScott is offline
 
Reply With Quote Quick reply to this message
Old 01-02-2014, 12:47 PM   #3
brewkinger
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
brewkinger's Avatar
Recipes 
 
Join Date: Sep 2012
Location: East Po-dunk, Vermont
Posts: 1,520
Liked 180 Times on 151 Posts
Likes Given: 213

Default

I am not familiar with "pressure barrels" so my comments address your process.

The "rinse" that you mention after sanitizing step is not necessary depending on the type of sanitizer being used. Once sanitIzed, rinsing could introduce unwanted pathogens.

As far as the sugar used, table sugar works as does corn sugar, brown sugar, or ANY sugar.
The only differences would be in the amount used. As above post mentioned, make a priming solution and put in barrel first and THEN transfer beer into barrel. More consistent and even mixture.
Not enough sugar will result in poor carbonation while too much sugar can create a pressurized bomb that can hurt or kill!
Be careful and ask questions if you are unsure.

__________________
Blackbird Brewing

PRIMARY: End of Summer Mish-Mash Ale
SECONDARY-NADA
SECONDARY-NOTHIN'
Conditioning and Drinking: Bass Ale Clone
Conditioning and Drinking:Regal Pale Ale
Conditioning and Drinking:Dirty Blonde Ale
Do not mistake my kindness for weakness. I am kind to everyone, but when someone is unkind to me, weak is not what you will remember about me.
brewkinger is offline
 
Reply With Quote Quick reply to this message
Old 01-04-2014, 02:26 PM   #4
BrettPreston
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2013
Posts: 56
Default

Thankyou for your replies. They were helpful and useful.

So, this morning I did it, moved it Into the pressure barrel. I took your bits of advice, sanitised everything that came I to contact with the beer, boiled water and mixed with 100g of sugar let cool then added to the barrel. Moved the beer into the barrel, carefully and did not take to much sediment with it. I use availinle round the lid to ensure a good seal. I have now left it in a warm around of my flat and will leave it there for around a week before moving to a cooler area.

I've used a calculator online to figure out the ABV of my ale. It states that it is around 3.5% however my instructions state it should be around 4.6%.

Will it rise in the barrel?

Could I of made a mistake to not of gotten to the correct AVB?

Thanks guys.

__________________
BrettPreston is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Pressure barrel leaker pressure Cobby1986 Bottling/Kegging 0 12-26-2013 09:04 AM
NE Major Issue with transferring from 1/2 barrel comercial keg into 3 cornies? H22W Bottling/Kegging 4 02-08-2013 02:57 PM
Transferring High Pressure Hot Water foamous Equipment/Sanitation 8 05-10-2012 04:30 AM
Secondary fermentation in a pressure barrel crazywildhorse Fermentation & Yeast 3 11-06-2011 10:25 PM
Transferring to pressure barrel Borbus Beginners Beer Brewing Forum 10 06-14-2009 02:40 PM