Spike Brewing 12.5 Conical Fermenter Giveaway - Enter Now!

Home Brew Forums > Home Brewing Beer > Extract Brewing > Yooper's DFH Clone 10 gallon question

Reply
 
LinkBack Thread Tools
Old 07-29-2012, 10:21 PM   #1
porky_pine
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2012
Location: portland, or
Posts: 114
Liked 10 Times on 7 Posts
Likes Given: 116

Default Yooper's DFH Clone 10 gallon question

I want to brew 10 gallons of this beer. Do I just double the amount of hops and extract? How much water should I start with? I just got a new Bayou 62 quart pot and want to put it to use! Cheers!

Recipe:

DFH clone

Batch Size: 5.00 gal
Boil Size: 2.5 gal
Estimated OG: 1.072 SG
Estimated Color: 13.1 SRM
Estimated IBU: 49.8 IBU

Boil Time: 60 Minutes

Ingredients:

Amount Item Type % or IBU
9.5 lbs Pale Liquid Extract (8.0 SRM) Extract 90.83 %
1 lbs Caramel/Crystal Malt 40L (40.0 SRM) Grain 9.17 %

1.25 oz Warrior [15.00 %] (60 min) Hops 26.7 IBU
(Read notes!)

1.00 oz Amarillo Gold [8.50 %] (35 min) Hops 10.0 IBU
1.00 oz Simcoe [12.00 %] (30 min) Hops 13.1 IBU
(Read notes!

1.00 oz Amarillo Gold [8.50 %] (Dry Hop 7 days) Hops
0.50 oz Simcoe [12.00 %] (Dry Hop 7 days) Hops

Notes:

Pacman yeast used, but any clean well attenuating yeast can be used. Try WLP001, Nottingham, or 1056 if pacman is not available.

Hops were added as continuous first warrior for the first 25 minutes ( approximately half at 60 minutes, then a little bit at a time until 35 minutes was left in the boil). Then the rest of the hops were mixed together, and added continuously at 35 minutes.

You can use dry malt extract instead of the liquid if you=d like- use 8 pounds of DME instead.

Directions:


Steep the crystal in a grain bag in 2.5 gallons of water at 150-155 degrees for 20 minutes. Remove the grains, and discard them. Bring that Atea@ to a boil. When it is boiling, remove it from the heat (take it OFF the burner!) And stir in the LME. Put it back on the burner, and bring it to a boil. When it is boiling, add approximately half of the warrior hops you have. Set the timer for 60 minutes. After that, continue adding a pellet or two or five, every minute or so, until there is 35 minutes left on your timer. Try to time it so you are out of warrior pellets at 35 minutes left. Mix the rest of the hops together in a bowl. When you have 35 minutes left, start adding those hops just a few at a time, trying to end with the last of them when your timer hits 0 and you turn the flame off. Chill the wort rapidly, add to your fermenter, and top up to 5 gallons with cool water. Check the temperature to ensure it is around 70 degrees, and pitch a neutral yeast like American ale yeast (1056), or dry yeast like nottingham or safale s05. Ferment until completely done, and then allow to rest. Two weeks is pretty good. Then, rack to a clean 5 gallon carboy and dry hop with the dryhopping hops. You can either just put them into the fermenter and rack onto them, or use a hops bag if you=d like. Just don=t pack them tightly, you want the beer to be in contact with the hops. Use two or three bags if you need them. After about a week, you can rack to a bottling bucket avoiding the hops chunks, and bottle. Prime as usual, with approx. 3.5- 4 ounces priming sugar for 5 gallons of beer. You may have less than 5 gallons, due to the hops sucking up some of the beer, that=s why 3.5-4 ounces is a good bet.

__________________
porky_pine is offline
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Fixed Gear Clone Question BlakeL Extract Brewing 2 07-25-2012 01:09 AM
5 gallon full boil question twah Extract Brewing 13 11-21-2011 01:30 AM
Newcastle clone - secondary question OliBrew Extract Brewing 4 02-12-2011 02:58 PM
Stone Ruination Clone w/ starter question forces Extract Brewing 15 12-16-2009 09:33 PM
AHS SNPA Clone recipe question... ohill1981 Extract Brewing 3 03-12-2009 10:30 PM