Spike Brewing 12.5 Conical Fermenter Giveaway!

Home Brew Forums > Home Brewing Beer > Extract Brewing > BYO's Method of Steeping Grains

Reply
 
LinkBack Thread Tools
Old 09-29-2010, 01:58 PM   #1
smmcdermott
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2009
Location: Connecticut
Posts: 423
Liked 2 Times on 2 Posts

Default BYO's Method of Steeping Grains

I was reading the most recent BYO magazine, which is centered on extrac brewing, and was curious what their process would be as I am always seeking new / better ways for my process. I was curious if anyone has ever done their method of steeping grains as I heat the water to 155 F and leave for 30 mins. Theres method is: When water reaches 140 F put grains in and continue to heat, once water temp reaches 170 F, about 20 mins, pull grains out.

I don't know about you guys, but it doesn't take my water 20 mins to go from 140 to 170. Also, isn't 170 high? Just curious what everyone else thinks. Thanks.

__________________
smmcdermott is offline
 
Reply With Quote Quick reply to this message
Old 09-29-2010, 02:03 PM   #2
Yooper
Ale's What Cures You!
HBT_ADMIN.png
Feedback Score: 0 reviews
 
Yooper's Avatar
Recipes 
 
Join Date: Jun 2006
Location: Upper Michigan
Posts: 60,582
Liked 4342 Times on 3157 Posts
Likes Given: 845

Default

170 degrees is the upper limit of the recognized "safe" temperature. By that I mean, you can be safe in not pulling out any tannins from the husks at temperatures of 170 or below. So, I'd say 170 is ok.

I'm sure that BYOs method is fine. What I recommend is a bit different though. I recommend always using 1.5 quarts of water per pound of grain and adding the grain bag when the water is 160-170 degrees. Stir it up, and let it sit for 30 minutes and keep the grain/water in the 150-155 range. Then remove the grains to a strainer and pour over 170 degree water to reach your boil volume.

The reason I recommend something a bit differently is actually because it's easier. Sometimes you have steeping grains only, sometimes steeping grains along with base grains, sometimes adjuncts, etc. If you treat every batch like it's a partial mash, you don't have to worry about any conversion or other issues. Using the same ratio of water and grains and the same temperature and the same time each brew really makes it easier in the long run.

Obviously, there is more than one correct way to do it, so I think everybody should do what they find most convenient.

__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006
Yooper is offline
 
Reply With Quote Quick reply to this message
Old 09-29-2010, 07:09 PM   #3
pericles
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2007
Location: Bryn Mawr, PA
Posts: 744
Liked 20 Times on 20 Posts
Likes Given: 1

Default

I follow BYO's procedure as you describe it. Always worked fine for me.

__________________
Primary 1: Hasty IPA
Primary 2:
Secondary: Soured Golden
Kegged: American Wheat
Bottled: Belgian Golden Ale.
Planning: American Amber
pericles is offline
 
Reply With Quote Quick reply to this message
Old 09-30-2010, 01:55 AM   #4
avidhomebrewer
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2007
Posts: 2,552
Liked 23 Times on 22 Posts

Default

That sounds good to me. When you heat your grains/water, just heat it much slower than you normally would. Don't go much higher than 170 (if at all), because then you start extracting tannins from the grain.

__________________
avidhomebrewer is offline
 
Reply With Quote Quick reply to this message
Old 09-30-2010, 04:36 AM   #5
brewingkitty
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2010
Location: Land of the Free
Posts: 578
Liked 1 Times on 1 Posts

Default

im ashamed to admit it, but i tried two 5g batches of partial mash before starting all grain.. and i botched both of them. seems simple, get water to temp x and soak for y time. had a hell ofa time figuring out why i was so low on og points!

__________________
.
"Back when I was in the pen, I used to beat my meat..."

"Damn ye, yellow-bellied sapsuckers; I'm a better man than all of ye milksops put together" - Blackbeard

"...I have really good sex moves; that I learned in China. I'm a sexual tiger; and feed on va-gine-a." - Jon Lajoie
brewingkitty is offline
 
Reply With Quote Quick reply to this message
Old 09-30-2010, 04:55 AM   #6
lumpher
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2009
Location: texas
Posts: 4,515
Liked 118 Times on 107 Posts
Likes Given: 15

Default

at 170, the husks of the grain start breaking down, and basically, the grain starts dissolving into the mix. husks have tannin, and that's bad for beer

__________________

Taps:
1: Yeti RIS clone
2: Mangrove Hefe
3: Barkshack Gingermead
4: Oatmeal Stout
5: Bavarian Wheat
6: Premium Lager

Fermenting: Concord Wine, ESB

lumpher is offline
 
Reply With Quote Quick reply to this message
Old 09-30-2010, 01:07 PM   #7
CrookedTail
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
CrookedTail's Avatar
Recipes 
 
Join Date: Jun 2010
Location: Patchogue, NY
Posts: 564
Liked 30 Times on 23 Posts

Default

I read the new issue of BYO. I do it a little differently. I put the grains into the cold water and heat it until it reaches 170, then let it sit at that temp for 30 minutes. I also noticed BYO didn't mention rinsing the grains after steeping, which is something I always do.

__________________
CrookedTail is offline
 
Reply With Quote Quick reply to this message
Old 09-30-2010, 08:06 PM   #8
MikeRoBrew1
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2010
Location: Minneapolis
Posts: 404
Liked 1 Times on 1 Posts
Likes Given: 242

Default

Shouldnt this be moved to the Grain forum?? This is the Extract forum.

__________________

My brew blog:
http://www.mikerobrew.blogspot.com
Follow me on Twitter @WakeMikey

MikeRoBrew1 is offline
 
Reply With Quote Quick reply to this message
Old 09-30-2010, 08:14 PM   #9
TomSD
Da Geek
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
TomSD's Avatar
Recipes 
 
Join Date: Aug 2010
Location: Lemon Grove, CA, CA
Posts: 1,449
Liked 31 Times on 22 Posts
Likes Given: 15

Default

This is about steeping and specialty grains I think the audience here would get more benefit from the discussion than full grainers.

I was going off old data when I started and was letting it go until I hit boil. Now I'm steeping at 165 for half an hour. I might go partial mash though now that I understand the process better. Meh, it is all about experimenting though as long as I know what the effects of my actions are (IE: tannins over 170, water/grain ratio for partial mash, etc) it is fun to mess around with it.

__________________

Johnson Controller rewire
| Keezer (FCM7SUWW) build | Love Controller box build | Soda Syrups/Concentrates

God is an imaginary friend for grownups., Walter Crewes (Morgan Freeman), The Big Bounce

Don't be afraid to ask dumb questions they're easier to handle than dumb mistakes!
TomSD is offline
 
Reply With Quote Quick reply to this message
Old 09-30-2010, 10:48 PM   #10
maxamuus
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2010
Location: Utah
Posts: 864
Liked 57 Times on 48 Posts
Likes Given: 34

Default

I brew the same way as Yooper.

__________________
maxamuus is offline
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
why do some recipes have steeping grains and some not tenchu_11 Extract Brewing 24 08-07-2010 02:55 PM
Steeping grains and extract karbinator Extract Brewing 14 03-17-2008 01:08 PM
Steeping grains Brewno Extract Brewing 12 10-27-2007 11:12 AM
Steeping grains rwillride17 Extract Brewing 11 11-02-2006 06:45 AM
Steeping grains sudsmonkey Extract Brewing 7 09-04-2005 05:58 PM