Ss Brewing Technologies Giveaway!

Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > strike temp ?
Reply
 
LinkBack Thread Tools
Old 10-12-2012, 05:20 AM   #1
ninkasi2012
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2012
Location: toronto, ontario
Posts: 51
Likes Given: 2

Default strike temp ?

Do you guys boil water to you exact strike temperature to meet the temp u want 2 mash @ or do you go a couple of degrees higher? Ive noticed that once I pour the water in my mash tun and stir for a minute or so I lose 2 degrees. Would it hurt aiming for a higher temperature ? My main concern is when I'm reaching a higher temperature like making a stout and I'm aiming for a mash temp of 152. Basically is there harm in aiming for 154-155 and stiring for a few minutes 2 drop to 152 ?
Thanks in advance!

__________________
ninkasi2012 is offline
 
Reply With Quote Quick reply to this message
Old 10-12-2012, 05:33 AM   #2
BBL_Brewer
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
BBL_Brewer's Avatar
Recipes 
 
Join Date: Feb 2011
Location: Kokomo, IN
Posts: 3,698
Liked 425 Times on 295 Posts
Likes Given: 320

Default

No that's fine. Or you could preheat your mash tun with some warm water before your add the grain and strike water. If you really want to dial it in, you could figure out your heat loss and compensate for it. Check out this thread. http://www.homebrewtalk.com/f36/new-...volume-358834/

__________________
Slots Down Brewery
Stick with the plan....not the sparge.


Never Ending Liquid Yeast - How to Farm Yeast and Freeze it.

BBL_Brewer is offline
 
Reply With Quote Quick reply to this message
Old 10-12-2012, 05:33 AM   #3
neosapien
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2012
Location: Dallas, TX
Posts: 714
Liked 140 Times on 99 Posts
Likes Given: 395

Default

no harm there. can stir like the dickens or keep some cool water on the side to add in if necessary.

__________________
neosapien is offline
 
Reply With Quote Quick reply to this message
Old 10-12-2012, 05:37 AM   #4
wickman6
Feedback Score: 3 reviews
Recipes 
 
Join Date: Sep 2011
Location: vernon hills, il
Posts: 644
Liked 61 Times on 48 Posts
Likes Given: 95

Default

I have overshot my temps by a few degrees and did exactly as you said, stir for a few minutes until it cools to my target temp. I haven't had any ill effects. I think the most important thing is that your sacc rest is at the proper temp. A couple minutes above shouldn't hurt anything.

__________________
wickman6 is offline
 
Reply With Quote Quick reply to this message
Old 10-12-2012, 05:39 AM   #5
kylevester
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2012
Location: Lafayette, IN
Posts: 226
Liked 15 Times on 12 Posts
Likes Given: 7

Default

It's fully dependent on your equipment and your procedures to determine your strike temp.

My mash tun, I add boiling water to it to pre-heat to about 100 deg, and I use BeerSmith to give me the temps to heat to. Typically, it's about 15 deg above my desired mash temp.

If I didn't pre-heat, I'd need to heat my strike water up probably 2 deg more.

It's fine to go a little high and then stir or add a small bit of ice to bring it down.

__________________
kylevester is offline
 
Reply With Quote Quick reply to this message
Old 10-12-2012, 12:26 PM   #6
hogwash
Minimally Exceptional
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
hogwash's Avatar
Recipes 
 
Join Date: Aug 2008
Location: Waynesboro, VA
Posts: 667
Liked 52 Times on 43 Posts
Likes Given: 16

Default

Agree with everyone else. I heat my tun with hot water, add my grains, then add my strike water. I shoot for about 11 degrees above my target mash temp. Sometimes I hit it on the nose and other times I have to stir and/or add cool water.

__________________
hogwash is offline
 
Reply With Quote Quick reply to this message
Old 10-12-2012, 01:44 PM   #7
ninkasi2012
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2012
Location: toronto, ontario
Posts: 51
Likes Given: 2

Default

thank you all for everyone's response!

__________________
ninkasi2012 is offline
 
Reply With Quote Quick reply to this message
Old 10-12-2012, 02:32 PM   #8
Homercidal
Moderator
HBT_MODERATOR.png
Feedback Score: 0 reviews
 
Homercidal's Avatar
Recipes 
 
Join Date: Feb 2008
Location: Reed City, MI
Posts: 23,518
Liked 2118 Times on 1520 Posts
Likes Given: 1162

Default

I'm late, but I'd like to add that in my experience, it's MUCH easier to aim a few degrees high and add some cool water to the mash than is it to try and heat up the mash with hot water. I use ice cubes too, by the way. Less liquid, more cooling.

Even with preheating I've been low with my calculations (well, beersmith's) so I usually aim 2-3 higher and if I hit it, in go the ice.

__________________
Homercidal is online now
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Strike Temp C-Rider All Grain & Partial Mash Brewing 9 07-06-2011 05:46 PM
What temp for strike what? Dick562 All Grain & Partial Mash Brewing 9 11-12-2010 11:47 PM
strike temp q's eljib All Grain & Partial Mash Brewing 7 10-18-2009 06:33 AM
Strike temp in BTP hoosbrewing Brewing Software 1 06-22-2009 01:54 AM
Keg MLT Strike Temp? Lil' Sparky All Grain & Partial Mash Brewing 7 02-02-2007 01:42 PM