Electric Brewing Supply 30A BCS Giveaway!


Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > Preboiling hard water?
Reply
 
LinkBack Thread Tools
Old 10-04-2010, 07:12 PM   #1
blkandrust
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2010
Location: Harrisonburg, Va
Posts: 396
Liked 8 Times on 7 Posts
Likes Given: 2

Default Preboiling hard water?

My well water is very high in Iron,would preboiling my strike water and letting it cool to strike temp have any positive effect on my beer?...I have been tasting a slight off tatste in my beers that I have narrowed down to my water..

__________________

Lady Astor-"If you were my husband,I would poison your drink"

Winston Churchill-"If you were my wife,I'd drink it"

blkandrust is offline
 
Reply With Quote Quick reply to this message
Old 10-04-2010, 07:23 PM   #2
Hermit
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2009
Location: Alternate Universe
Posts: 2,246
Liked 67 Times on 57 Posts
Likes Given: 10

Default

Check out the new sticky in the brew science forum for a quick water primer.

__________________
Hermit is offline
 
Reply With Quote Quick reply to this message
Old 10-04-2010, 10:10 PM   #4
tunoffun
Feedback Score: 0 reviews
Recipes 
 
Join Date: Oct 2010
Location: AZ
Posts: 239
Liked 8 Times on 8 Posts
Likes Given: 3

Default

as far as I'm aware, boiling your water isn't going to do anything to precipitate out iron. In contrast, it will probably make your problems worse, since you'll be concentrating the iron content through evaporation.

my tap water here is substandard for other reasons, so I've opted to build my water from scratch using RO water & salts. Water & Ice stores here sell RO for .40 / gallon, and the cost of the salts for even moderately hard water are negligible. For less than $9.00 I can custom build all the water (mash, sparge, & top-off) needed for a 10-gallon batch and precisely control the flavor profile (among other things) as well.

__________________
tunoffun is offline
 
Reply With Quote Quick reply to this message
Old 10-05-2010, 01:32 PM   #5
sjlammer
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2007
Location: Albany, NY
Posts: 576
Liked 5 Times on 5 Posts
Likes Given: 1

Default

to remove iron you would have to add sodium hypo (bleach) (allow it to sit for 10-30 minutes of contact time) to precipitate out the iron, then, run the water through a filter, to remove the precipitate, then run the water through a carbon filter to remove the chlorine.

lot of work if you ask me. I would just buy RO/distilled water.

__________________
~"A fine beer may be judged with only one sip, but it's better to be thoroughly sure.”

On Deck: Spruce APA, Chambord Fortified Chocolate Porter, Imperial IPA

Primary:
Primary:
Secondary: Belgian Dark Strong Ale
Conical:
Lagering: None
Kegged/Drinking: Cascade, Cent., Amarillo Pale Ale
Kegged/Drinking: Belgian Pale Ale (HG yeast for yeast cropping see above)
Bottled: ESB
sjlammer is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Central Jersey Hard Water, Good for Mashing? TVarmy All Grain & Partial Mash Brewing 8 07-08-2012 12:03 AM
Can I Boil Too Hard? RonRock All Grain & Partial Mash Brewing 7 03-11-2009 07:12 AM
AG is not nearly as hard as it sounds! SkinnyShamrock All Grain & Partial Mash Brewing 7 03-09-2009 07:32 PM
Brewing with hard water... The Pol All Grain & Partial Mash Brewing 18 01-11-2008 03:01 AM
Hard water but want to do 1st AG suggestions rra24403 All Grain & Partial Mash Brewing 12 05-03-2007 11:31 PM