Happy HolidaySs Giveaway - Last Sponsor Giveaway of the Year!

Come Enter the BrewDeals/FastFerment Giveaway!


Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > My first AG brew..."fun."
Reply
 
LinkBack Thread Tools
Old 02-25-2013, 02:36 AM   #1
stavale8099
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2013
Posts: 63
Likes Given: 2

Default My first AG brew..."fun."

Ok, well whoever would like to hear a good "disaster" story for my first AG brew. I take a lot out of it though as I learned a lot...I think...
Here was my recipe:
7.5lb maris otter
1lb instant oats (day before I baked @ 375 for an hour - nice and toasty)
0.5lb flaked barley
0.5lb chocolate
0.5lb crystal 60L
0.2lb carapils
0.2lb roasted barley
2oz East kent 60 min.
single temp infusion @ ~154
S-04 yeast

Decided to brew an oatmeal stout for my first AG in a new (used) MLT I purchased which was 8 gal w/ a false bottom which prob held ~ 1 gallon - This was my first mistake as I did not account for the extra space on the bottom when I calculated to mash in with 1.25 qt/gal. I heated up JUST enough strike water to to calculate for 1.25. I should start off by saying that I have a ~2.5 gal and a ~3.5 gal boil pot so I knew that things would be tight. Anyways after realizing my mistake for not taking into account the false bottom I had to quickly heat up more water. My target temp was 154 and after adding the first batch of strike water of course a gallon of it drained right through the mash and brought the mash temp only upt o about 140. So, I had a good 15-20 min @ 140. Final water/grain ratio was 1.68 and I mashed @ ~152 for an hour.
Knowing I needed to vorlauf and sparge, I heated up some more water. Only having a 3.5 gal pot (my biggest) I was only able to collect this much of the "first runnings" and vorlauf (sparge water heating up in my 2.5 gal). However, I also didn't think that I should vorlauf a little slower than I did so instead of capturing all the small particles on top of the grain bed, I recirculated too quickly and just mixed up the entire bed again and again got small particles in my first runnings.
First runnings ~14 quarts - Gravity 1.05
At this point I realized that if I was going to sparge with as much as I SHOULD, I was going to run out of boil pots very quickly. So, I batch sparged with another 6 quarts or so for 15 minutes. I believe that the gravity of my second runnings was ~1.03. It was much less sweet but I was out of room in my boiling pots at this time (I now had 5 gallons pre-boil) so I couldn't sparge down to gravity of 1.01. So, now I mixed my 1st and second runnings and my gravity was 1.042.
I had two VERY full pots of wort for the boil, which certainly made the hot break interesting but I did not get a boil-over.
I cooled the wort with a copper coil heat displacer which I also accidentally touched while adding some irish moss so that sucked. Hard. It also sucked that the 3.5 gal pot took 30 minutes longer to start to boil than the 2.5 gal pot so everythign was somewhat staggered.
So, I lost ~1 gal to the boil and my gravity post-boil was 1.064. F-that, I wanted a 5-gallon batch so I spiked it wtih 1 gal of cold water and the final pitchign temp was ~70 degrees.
Final OG 1.05 for fermentation.
To the boil I also added a few teaspoons for urea/diamm phos. and some yeast for nutriets. I couldn't find any Wyeast so I used dry S-04 so I was paranoid about lack of nutrients. I didn't have any zinc or anything to add so hopefully there is enough in my water.
I sprinkled my yeast on top of the wort (I've done this before with previous non-AG batches) and then waited 15 minutes to stir it in. BUT this time (this didn't happen last time) it just sunk and so was not present after 15 minutes. I hope it lives.

Anyways...so finally I have a 5 gallon batch that is full of small grain particles. Hopefully these just settle out and don't affect the flavor. I know this is an aggressive yeast so if its not full-on fermenting by tomorrow night then there is probably an issue.

I DO know that next time I need to have a bigger second boil pot (we do it all in teh kitchen and don't have a gas burner nor the room for a large pot at this point so need to do split boil for now.)

Thoughts? Ideas? what should/shouldn't I do nxt time?
Thanks!

__________________
stavale8099 is offline
 
Reply With Quote Quick reply to this message
Old 02-25-2013, 02:43 AM   #2
stavale8099
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2013
Posts: 63
Likes Given: 2

Default

According to the calculators I got 74% efficiency

__________________
stavale8099 is offline
 
Reply With Quote Quick reply to this message
Old 02-25-2013, 03:02 AM   #3
GrogNerd
Why must it always be pandemonium?
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
GrogNerd's Avatar
Recipes 
 
Join Date: Oct 2012
Location: Sterling, VA
Posts: 3,623
Liked 913 Times on 630 Posts
Likes Given: 116

Default

Quote:
Originally Posted by stavale8099 View Post
Thoughts? Ideas? what should/shouldn't I do nxt time?
Thanks!
#1 - figure out how much dead space you have with that false bottom

#2 - don't worry so much about that 140° rest. from Palmer's How to Brew: "he typical Protein Rest at 120 - 130°F is used to break up proteins which might otherwise cause chill haze and can improve the head retention. This rest should only be used when using moderately-modified malts, or when using fully modified malts with a large proportion (>25%) of unmalted grain, e.g. flaked barley, wheat, rye, or oatmeal"

so, temp is a little off and your proportion of unmalted grain isn't >25%, but so what. with this and your carapils, you'll have some good head retention.

#3 - 74% efficiency & it seems you hit some good pre-boil gravities.

#4 - get a BIGGER KETTLE. 14qt is good for extract ½ boils, but AG full boils you need an 8 to 10 gallon kettle.

otherwise, sounds like a pretty good first AG brew day!
__________________

"Why must it always be pandemonium?" - George Mueller/Nelson Van Alden

"Beer. Good." - Words of House Grog

drinking: Wojtkowiak Piwo, CLB's Barleywine, 8Hearted Pale Ale, O'Rob's Dry Irish Stout, DB8PT Session Ale, Wojtkowiak Grodziskie - bottle conditioning: Otto M. Gourd Pumpkin Barleywine, Jewel Thieves Apple Wine, CLB's Barleywine 1.2

GrogNerd is offline
 
Reply With Quote Quick reply to this message
Old 02-25-2013, 03:09 AM   #4
stavale8099
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2013
Posts: 63
Likes Given: 2

Default

So after some looking into this further I entered the wrong number of points for my base malt so looks like 71%...oh well....


Question - do you think there are enough nutrients for fermentation?
Is the final water to grain ratio what the amount of water which is actually touching the grain above the false bottom or does it include that water?
The protein rest was completely accidental since I only realized I wasn't spiking with enough water at 168 to bring the temp of the grain up to where I wanted it
Bigger kettle - duly noted ! Lets hope my electrics stovetop can handle it.

__________________

---------------------------------------------
Primary: Patersbier
Secondary: Quad (Pious), Honey Kolsch
Kegged: Honey Kolsch
Bottled: Belgian strong
Bottled: Vanilla Choc Oatmeal Stout

stavale8099 is offline
 
Reply With Quote Quick reply to this message
Old 02-25-2013, 03:27 AM   #5
GrogNerd
Why must it always be pandemonium?
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
GrogNerd's Avatar
Recipes 
 
Join Date: Oct 2012
Location: Sterling, VA
Posts: 3,623
Liked 913 Times on 630 Posts
Likes Given: 116

Default

final water to grain ratio is what is touching the grain above the false bottom

I ran into the same problem my first all-grain in a Zapap and also had an unscheduled protein rest.

beer turned out friggin tasty. the last bottles are in the fridge now

have never had the need to add any nutrients for fermentation.

and your particles will settle out, given enough time in the fermenter

__________________

"Why must it always be pandemonium?" - George Mueller/Nelson Van Alden

"Beer. Good." - Words of House Grog

drinking: Wojtkowiak Piwo, CLB's Barleywine, 8Hearted Pale Ale, O'Rob's Dry Irish Stout, DB8PT Session Ale, Wojtkowiak Grodziskie - bottle conditioning: Otto M. Gourd Pumpkin Barleywine, Jewel Thieves Apple Wine, CLB's Barleywine 1.2

GrogNerd is offline
 
Reply With Quote Quick reply to this message
Old 02-25-2013, 03:35 AM   #6
beatlebum
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2011
Location: new orleans, louisiana
Posts: 9
Liked 1 Times on 1 Posts
Likes Given: 4

Default

best advice is probably just to brew again, and again and again. every one's process is a bit different and every time you try something new - such as your first AG batch - it'll be a bit hectic and terrifying. just keep doing it and it becomes automatic.

though i'd add that from my experience, (aside frmo skipping protein rest as mentioned above) grain/liquor ratio isn't terribly important for a mash. yeah, thicker mashes are better for non-fermentable sugars and thinner for fermentable, but from my limited experience, not much.

more important is to get to the right temp off the bat because it's such a hassle to deal with raising/lowering mash temp. i always use about the same amount of water and adjust strike temp between 10-15 degrees F + target mash temp depending on total grain bill. not particularly scientific, but usually werks good!

__________________
beatlebum is offline
 
Reply With Quote Quick reply to this message
Old 02-25-2013, 03:49 AM   #7
Cyclman
I Sell Koalas
HBT_LIFETIMESUPPORTER.png
Feedback Score: 1 reviews
 
Cyclman's Avatar
Recipes 
 
Join Date: Jan 2013
Location: Aurora, CO
Posts: 4,606
Liked 425 Times on 373 Posts
Likes Given: 136

Default

homebrewfinds has a 10G kettle for $37, delivered. Otherwise, it sounds like in the end your beer will be great.

__________________

Give a man a beer, waste an hour. Teach a man to brew, and waste a lifetime! Bill Owen quote

Join the Beacon Point (Aurora, CO) Brewclub on Facebook- casual, fun brewing, drinking, socializing!

Cyclman is offline
hopstupid Likes This 
Reply With Quote Quick reply to this message
Old 02-25-2013, 05:31 AM   #8
Walking_Target
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2011
Location: Peterborough, ON
Posts: 228
Liked 12 Times on 11 Posts
Likes Given: 4

Default

After lots of reading before doing this myself, I gotta say, anything over 70% total efficiency on you first brew is pretty darn good. I got a brewhouse (in carboy) efficiency of 72% on my first batch and was quite happy.

__________________

Fermenting - Pomegranate Mead (3g), Acerglyn

Kegged - Modified Bee Cave IPA, Calypso Pale

Bottled - Brown ale, Pomegranate Mead, Orange Apfelwein

Walking_Target is offline
 
Reply With Quote Quick reply to this message
Old 02-25-2013, 01:56 PM   #9
stavale8099
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2013
Posts: 63
Likes Given: 2

Default

the lady decided to cook dinner right when the mash was finishing up which took up half the kitchen as well. Also when I burned my hand on the copper coil while adding the moss it sent the moss flying everywhere so I'm not quite sure how much actually made it in haha.

Do you guys monitor the mash pH pretty frequently? I did a mini mash a month ago (my first mash) and stood over it the entire time checking the pH and starch conversion every 10 minutes. This time I didn't even think of it until I was about to start the boil. Both seemed to be around 5.5 which from what I've seen is ideal. What ingredients would require a more frequent mash ph check?

__________________

---------------------------------------------
Primary: Patersbier
Secondary: Quad (Pious), Honey Kolsch
Kegged: Honey Kolsch
Bottled: Belgian strong
Bottled: Vanilla Choc Oatmeal Stout

stavale8099 is offline
 
Reply With Quote Quick reply to this message
Old 02-25-2013, 02:30 PM   #10
MI_Troll
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2012
Posts: 61
Liked 8 Times on 7 Posts

Default

Up until recently I was a two pot on the stove brewer. I used two 16qt pots, one I had from extract days, another I grabbed at Wally World for $12 to get up to 8 gallons of boil capacity. I always sparged into my bottling bucket and then dispensed into my pots. With lots of foam control I was able to take the liquid levels up to within 1/4 in of the top without making a mess. 90 minute boils were a bit trickier because I had to boil off some wort to make room for some more. I now have a 10 gallon pot that straddles two burners. It takes all the fun out of partially filling pots to be able to finish sparging and keeping multiple stopwatches running for 8 hops additions across multiple kettles. I miss the Vegas-like excitement of wagering wether the bottling bucket was going to give out while filled to the rim with 160 degree wort. Don't cave to the temptation of having the ability to boil everything in one pot, it makes brewing dull.

__________________
MI_Troll is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
"Brew House" vs "Actual Mash" Efficiency huntsman General Beer Discussion 5 12-07-2013 09:58 AM
Such a thing as "Black Friday" or "cyber Monday" for homebrew supply? StusBrew General Beer Discussion 37 11-30-2013 12:07 AM
Woof...HUGE difference with "fresh" vs "not-so-fresh" commercial brew scrambledegg81 General Beer Discussion 15 08-20-2011 02:25 PM
Taking my winemaking skills from "cook" to "chef" levels. JasontheBeaver Wine Making Forum 5 07-28-2011 08:49 PM
"Hello, World," or "Did I Ruin My Brew Already" dwint Beginners Beer Brewing Forum 17 09-21-2010 04:48 AM



Newest Threads

LATEST SPONSOR DEALS