phecke

Recipes 

So I did my first AG brew this past Sunday, everything went smoothly and had no big surprises or problems. I'm making an amber ale, and my recipe is as follows:

Phecke's Amber Ale
10-B American Amber Ale
Date: 8/8/10

Original Gravity: 1.058 (1.045 - 1.060)
Terminal Gravity: 1.015 (1.010 - 1.015)
Color: 19.12 (10.0 - 17.0)
Alcohol: 5.72% (4.5% - 6.2%)
Bitterness: 36.2 (25.0 - 40.0)

Ingredients:
10.0 lb 6-Row Brewers Malt
2 lb American Caramel 80°L
1.0 oz Cascade (5.5%) - added during boil, boiled 60 min
1.0 oz Cascade (5.5%) - added during boil, boiled 20 min
1.0 oz Cascade (5.5%) - added during boil, boiled 5 min
1.0 lb Victory® Malt
1.0 ea WYeast 1056 American Ale

I'm not quite in the "accepted ranges" but whatever, just trying some stuff on my own. Anyway, I came close to my expected OG and came in at 1.056, and pitched a 1L starter that took off VERY quickly when I made it, just healthy yeast I suppose. I had good fermentation going with 3-4 hours and it continued for the the next 48-72 hours. It all but stopped after that, so I checked the gravity today just to see where I was and to be sure I didn't have a stuck fermentation. I measured it right at 1.008 which is a little low. I'm not complaining, I like dryer beers and it tastes fine right now, I'm just curious as to what would cause such a low FG. I did mash at about 150˚F for 70 minutes, so I suppose that could be a contribution as well as just good healthy yeast.

What say you HBT?

Yooper

Recipes 

Mashing at 150 for 70 minutes would give you a more fermentable wort, and hence a drier beer, than if you mashed at a higher temperature. I usually mash AAAs at 153-154 for 45 minutes to an hour. I only mash a couple of beers at 150 or less- usually IIPAs or beers that I want to finish dry. I mash beers that I want "thick" and dextrinous at 156-158. Temperature really plays a big part in the finish of a beer.

Another thing to keep in mind is that your thermometer is only 2 degrees off, you could have mashed at a very low 148! I know that I had issues like that a couple of years ago, and all of my beers were finishing under 1.010, that's why I mentioned it.

Of course, using two pounds of crystal malt should have given you a higher amount of residual sweetness and a higher FG so I'm surprised it did finish at 1.008.

__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006

phecke

Recipes 

I figure it mostly is the mash temperature. I was aiming for 154˚, came in at 151˚, and dropped to 150˚ during the mash, but it was my first run so I was happy. That's a good point that the thermometer could be off. This little digital one I have seems to be dead on at boil, but about 2 degrees warm at freezing, so who knows where it's at in the 150's range. Any recommendations for a good and accurate digital thermometer with a probe on a wire?


Yeah, my local home brew store only sells grain by the pound, so while I only wanted to use 1.5 pounds of crystal, I had to buy 2 pounds. When I doughed-in, I wasn't paying attention and dumped the whole 2 pounds in instead of measuring it out. Whoops.

ajf

Recipes 

Where did you get your "accepted ranges" from?
I know that Beersmith pays no attention to the mash temperature (which can have a considerable affect on attenuation), but I use Promash (which doesn't even try to guess the FG).
I did some research on this a few days ago, and find that I get 75% to 80% apparent attenuation when using WLP002 with a mash using 100% grain, yet White Labs say 63% - 70%. I checked with White Labs and they confirmed that their published attenuation figures are apparent, rather than real.

-a.

__________________
There are only 10 types of people in this world. Those that understand binary, and those that don't.

suprchunk

Recipes 

Probably the BJCP Styles. I'm only, of course, guessing based on the part of the post that stated "10-B American Amber Ale". One of these days I will start brewing the styles so I can sample what BJCP purports to be the style.

And to the OP, yes that low a mash will usually yield a drier finished beer. Next time try a bit higher and compare the two to really see the difference subtle changes can make.

phecke

Recipes 

Exactly right, I rarely followed the styles and ranges to the letter though. I just used them as a guide to get me in the ballpark of what I wanted my beer to taste like.

I definitely will next time, I don't mind a drier beer, I was just curious as to why my FG was lower. Thanks for the input everyone!