New Giveaway - Wort Monster Conical Fermenter!

Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > False bottom help.




Reply
 
LinkBack Thread Tools Display Modes
Old 04-22-2009, 01:41 AM   #1
zanemoseley
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2009
Location: Cookeville, TN
Posts: 564
Liked 1 Times on 1 Posts

Default False bottom help.

Ok I have a 10G Rubbermaid, a Zymico ball valve kit and the false bottom adapter kit that MW sells. I thought it would be a quick install however it was a bit of a PITA. The ball valve and bulkhead took two huge pairs of vise grips to tighten but works great with no leaks. My plan was to the install the adapter and put in the false bottom. Found out the hard way that the FB doesn't fit in well after the adapter is installed so I had to force the FB in a bit which scraped up the cooler a bit, hopefully the FB doesn't have to be taken in and out much. Then I got to try and connect the two barbed fitting with the semi-stiff braided tubing that was supplied. Its a total PITA to get on, I cut it to length and ended up putting a slit on each end so it would go over the barb easier. Then the SS hose clamps they supply are too small and won't engage when they're set loose enough to fit over the tubing/barbs.

So I'd like to know how you guys run your tubing so its easy to install, I did a straight run however I could see how a loop might be easier or even not lining up the barbs in a line so the tubing has to bend. I wish MW wouldn't have cheaped out on the tubing, they should have included some silicone tubing instead of the cheap stiff stuff. Right now I have the tubing connecting the two barbs but it has splits on the ends and no hose clamps. I'm brewing this weekend and will probably have to pick up some bigger clamps. I will probably buy a foot of 3/8" Silbrade on my next order to do it right like MW should have done.

If any of you guys have pictures of the inside of your cooler showing the connections that would be great.



__________________
zanemoseley is offline
 
Reply With Quote Quick reply to this message
Old 04-22-2009, 01:49 AM   #2
The Pol
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2007
Posts: 11,616
Liked 49 Times on 46 Posts

Default

Okay, braided vinyl is HARD stuff... silicone would be better.

BUT, I have the same thing you have. You need to cut the hose to the correct length #1... to get a straight run. Then boil some water, place ONE end of the hose in it and get it nice and supple, slide over the barb on the false bottom

Repeat with the other end now... place the bottom in the tun and slide that end over the other barb.

Complete.

After a day on the barbs, the hose stretches and it is much easier to get on and off.

__________________
The Pol is offline
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options
Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
SS false bottom for 10 gallon cooler..grain all stuck under outside and filled bottom discgolfin All Grain & Partial Mash Brewing 10 05-06-2011 04:58 PM
Pickup location from bottom on false bottom Darboy Equipment/Sanitation 1 03-01-2009 06:58 PM
Which false bottom to use? dblvsn Equipment/Sanitation 2 05-11-2008 02:28 AM
False bottom? hopsalot Beginners Beer Brewing Forum 3 11-11-2007 11:18 PM
False Bottom Dark_Ale Equipment/Sanitation 3 01-24-2005 09:55 AM