Kegconnection Complete Starter Kit and More Giveaway!


Home Brew Forums > Home Brewing Beer > Bottling/Kegging > Where to place CO2 manifold in Danby DKC645BLS

Reply
 
LinkBack Thread Tools
Old 08-03-2012, 05:15 PM   #1
JayMac
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2012
Location: Guelph, Ontario
Posts: 252
Liked 10 Times on 9 Posts
Likes Given: 5

Default Where to place CO2 manifold in Danby DKC645BLS

Hey guys,

I just ordered all my parts in to install a second tap to my kegerator so I'll be able to have two homebrews on tap (one light session beer for the friends and drinking nights, then a nice IPA for after work!).

I was wondering if anyone has drilled holes inside their Danby DKC645BLS? I don't want to drill anywhere if I don't know where cooling coils or electrical wiring is. I hope to drill into the left side, near the top, close to the door. This will make it easier for force carbing, will keep it out of the way of kegs (when two in, I keep on at the back, and one on the right), and will allow me to take kegs off CO2 easily.

What do you think? Will this spot work? Or is this a dangerous place to drill? Oh, and don't worry, I just cleaned the fridge! It had been out of operation for a while and got pretty nasty!

img_0279.jpg  
__________________
JayMac is offline
 
Reply With Quote Quick reply to this message
Old 08-04-2012, 01:06 PM   #2
chris41
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2012
Location: Cleveland, OH
Posts: 44
Default

Your manifold should fit snugly into the rack slot below (looking at your pic) and therefore not require any drilling.

__________________
chris41 is offline
 
Reply With Quote Quick reply to this message
Old 08-05-2012, 08:25 PM   #3
JayMac
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2012
Location: Guelph, Ontario
Posts: 252
Liked 10 Times on 9 Posts
Likes Given: 5

Default

Quote:
Originally Posted by chris41 View Post
Your manifold should fit snugly into the rack slot below (looking at your pic) and therefore not require any drilling.
Just tried... its so incredibly close. It stays, but if tugged on it will fall. It'll work temporarily, but I'd like to have it secured. Thanks for the suggestion!

I wish I had a wiring diagram so I could tell where the electrical is!
__________________
JayMac is offline
 
Reply With Quote Quick reply to this message
Old 02-05-2013, 10:34 PM   #4
nate_e
Feedback Score: 0 reviews
Recipes 
 
Join Date: Oct 2012
Posts: 26
Default Bump...

I'm in the same boat, just got a manifold to put in a Danby DAR440. Did you end up mounting yours where you had it in the picture?

__________________
nate_e is offline
 
Reply With Quote Quick reply to this message
Old 02-06-2013, 06:16 AM   #5
JayMac
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2012
Location: Guelph, Ontario
Posts: 252
Liked 10 Times on 9 Posts
Likes Given: 5

Default

Actually, My kegerator broke down just before I was going to install it. I got a full refund, and put that towards building my own keezer.

Sorry I wasn't much help, but good luck!

__________________
JayMac is offline
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Danby dkc645bls Not Cooling vwjet2001 Bottling/Kegging 1 08-13-2012 07:29 PM
Danby dkc645bls Not Cooling vwjet2001 Bottling/Kegging 0 07-30-2012 09:44 PM
Question for Danby DKC645BLS owners zman Bottling/Kegging 9 01-07-2012 05:58 PM
Modifying a Danby DKC645BLS for a 2 or 3 tap tower zman Bottling/Kegging 10 01-19-2011 06:22 AM
Danby DKC645BLS experience? jelsas Bottling/Kegging 3 07-31-2007 02:19 PM