Get your HBT Growlers, Shirts and Membership before the Rush!


Home Brew Forums > Home Brewing Beer > Bottling/Kegging > Seeking Confirmation on CO2 Regulator Valves
Reply
 
LinkBack Thread Tools
Old 05-16-2012, 10:51 AM   #1
kleinishere
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2012
Location: Los Angeles, CA
Posts: 16
Likes Given: 1

Default Seeking Confirmation on CO2 Regulator Valves

Hi all,

I'm about to place an order for my 3 keg system but am hoping for your all's confirmation regarding CO2 regulator valves.

A photo of my dual regulator is attached to the post.

I would like to make this usable for 3 kegs w/ 2 unique pressures.

The suggested pieces:

-3 x Gas Shut-off valve - 1/4 NPT x 5/16 Hose Barb with check valve ( http://www.ritebrew.com/product-p/843684.htm )
-1 x Y-Splitter ( http://www.ritebrew.com/product-p/843471.htm )

The idea would be to first remove the current threaded valves and then replace one with a gas shut-off valve, the other with the y-splitter. Y-splitter would be furthest from tank hook-up as it'll be lower pressure at all times, non-split valve may force carbonate at times.

Although it may seem obvious, if you all could chime in to make sure this approach is the most direct and cost effective, I'd be super appreciative. If anything doesn't make sense, I'll be happy to clarify.

Thanks!

photo3.jpg  
__________________
kleinishere is offline
 
Reply With Quote Quick reply to this message
Old 05-16-2012, 07:38 PM   #2
audger
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2011
Location: ., Connecticut
Posts: 1,497
Liked 40 Times on 40 Posts
Likes Given: 1

Default

sounds good. you can also buy 1/4" stainless steel 'T's and just have one end going to the regulator, and the other two go out to your gas disconnects.

that Y splitter is essentially the same thing, but you would have to also buy hose barbs with it.

__________________
audger is offline
 
Reply With Quote Quick reply to this message
Old 05-16-2012, 09:11 PM   #3
kleinishere
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2012
Location: Los Angeles, CA
Posts: 16
Likes Given: 1

Default

Quote:
Originally Posted by audger
sounds good. you can also buy 1/4" stainless steel 'T's and just have one end going to the regulator, and the other two go out to your gas disconnects.

that Y splitter is essentially the same thing, but you would have to also buy hose barbs with it.
Thanks so much for taking a look and the advice.

If I were to go stainless T with barbs, it would be cheaper but I'd lose the check valve functionality, correct?

As this is my first time kegging, I think I want to pay the premium for some check valves and protecting my regulator, if I understand their role correctly.
__________________
kleinishere is offline
 
Reply With Quote Quick reply to this message
Old 05-17-2012, 03:14 PM   #4
audger
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2011
Location: ., Connecticut
Posts: 1,497
Liked 40 Times on 40 Posts
Likes Given: 1

Default

as long as one check valve between the regulator and any kegs, it doesnt matter very much if there isnt one between the kegs themselves. it is nice to have one ball valve and check valve on each gas line, but if you are trying to do it cheaply- the same thing can be done with a $4 tee

the only major instance where you need a check valve is if you overfill your keg to a level that is above the short gas dip tube. only then can beer travel up the gas line. if you dont overfill your kegs, you wont have problems. and as long as there is one between the kegs and the regulator, if beer travels up the gas line of one keg and gets into the other keg, its not the end of the world.

http://stores.kegconnection.com/Cate...=*Parts%3ATees

__________________
audger is offline
 
Reply With Quote Quick reply to this message
Old 05-18-2012, 01:41 AM   #5
kleinishere
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2012
Location: Los Angeles, CA
Posts: 16
Likes Given: 1

Default

Quote:
Originally Posted by audger View Post
as long as one check valve between the regulator and any kegs, it doesnt matter very much if there isnt one between the kegs themselves. it is nice to have one ball valve and check valve on each gas line, but if you are trying to do it cheaply- the same thing can be done with a $4 tee

the only major instance where you need a check valve is if you overfill your keg to a level that is above the short gas dip tube. only then can beer travel up the gas line. if you dont overfill your kegs, you wont have problems. and as long as there is one between the kegs and the regulator, if beer travels up the gas line of one keg and gets into the other keg, its not the end of the world.

http://stores.kegconnection.com/Cate...=*Parts%3ATees
Fantastic. Thanks for the advice and clarification. Re: dip tube, etc., that makes a lot more sense about when the check valve comes into play.
__________________
kleinishere is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Kegging Process Confirmation JPHussey Bottling/Kegging 4 04-01-2012 09:50 PM
Seeking kegging wisdom. ATXweirdobrew Bottling/Kegging 15 08-14-2011 02:54 AM
Make a dual regulator into a single regulator set up fishnfever Bottling/Kegging 4 05-04-2011 12:23 AM
Regulator Chck Valves Wronguy Bottling/Kegging 6 03-31-2011 01:03 AM
Shut-Off Valves and Integral Check Valves HenryHill Bottling/Kegging 6 01-21-2011 10:50 PM



Newest Threads

LATEST SPONSOR DEALS