Kegconnection Complete Starter Kit and More Giveaway!


Home Brew Forums > Home Brewing Beer > Bottling/Kegging > Sanyo 4912 draft tower stabilization mod and stainless steel rail install tips

Reply
 
LinkBack Thread Tools
Old 03-09-2007, 01:23 AM   #1
sirsloop
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2006
Location: South River, NJ
Posts: 2,592
Liked 16 Times on 15 Posts
Likes Given: 1

Default Sanyo 4912 draft tower stabilization mod and stainless steel rail install tips

So I had test fit my beer tower on my Sanyo 4910 while I waited for my stainless steel rails to arrive. I noticed that when you pulled on the faucet, the plastic was lifting up off the fridge and bending slightly, making the beer tower feel flimsy.

I stopped in at lowes and picked up some thin walled aluminum angle iron. It was 1/16" (wall thickness) x 1/2" x 3/4" x 50"and cost ~6 bucks. I used my dremel to notch the plastic support bars that go around the 8x8" square. I cut the angle iron to length, drilled holes, and used some "Truss Washer Lath Screws" - 8 x 9/16" to secure the aluminum to the 8x8" MDF.

After it was installed this made the beer tower VERY secure feeling. Well worth the ~10 bucks and 30 minutes to install.





I also installed some stainless steel rails for the top of the kegerator. The bars I used were 9-9/64" and 19-7/32", found here: http://www.leevalley.com/hardware/pa...521,46758&ap=1

I wanted to have more than just little machine screws holding this on, so I picked up 6 - 1/4" x 1-1/4" fender washers to support the bars ($1 and change). Also, the machine bolts that are included with the rails are too large. You need to pick up 6 - 8-32 x 3/8" machine bolts to replace them ($1).

At least on my 4910, the fender washers fit PERFECTLY into the rounded plastic support (see the top washers above). The ~20" wide support bolts line up PERFECTLY - just push the washers into the corners and drill. Obviously, check on yours before you take my word, but thats what I did. I eyeballed the other 4 holes, setting the mounting hole 1-1/2" down from the edge of the washer, and slightly out towards the outside. I used washers here too, and simply cut away the plastic support where needed.

This also helped reinforce the plastic on the fridge, resulting in a VERY solid feeling beer tower!!




I should have beer flowing this weekend!!!!

__________________
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ~~~~~~
~~~~~~~~~~~___//_ ____________________________~~~~~~~~~~~
~~~~~~~~~_/ [][]| | /```\/```\/```\/```\/```\ |~~~~~~~~~~
~~~~~~~_/_______| |____NOW TRIPLE HOPPED______|~~~~~~~~~~
~~~___/[_]| 00 /| | \,,,/\,,,/\,,,/\,,,/\,,,/ |~~~~~~~~~~
~~|___|___|___/_| |___________________________|~~~~~~~~~~
~~|=(*)[________]==(*)(*)=| \________/=(*)(*)=|~~~~~~~~~~

Last edited by sirsloop; 03-09-2007 at 01:42 AM.
sirsloop is offline
 
Reply With Quote Quick reply to this message
Old 03-09-2007, 03:25 AM   #2
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
Vendor Ads 
Feedback Score: 2 reviews
 
Bobby_M's Avatar
Recipes 
 
Join Date: Aug 2006
Location: Whitehouse Station, NJ
Posts: 21,836
Liked 910 Times on 606 Posts
Likes Given: 26

Default

Alright so I'm getting jealous of everyone that has a living-quarter acceptable, pretty kegger. Mine is such a huge noisy beast. Well, it does hold 5 kegs, so...

__________________
BrewHardware.com
Sightglass, Refractometer, Ball Valve, Weldless bulkhead, Thermometer, Decals, Stainless Steel Fittings, Compression Fittings, Camlock Quick Disconnects, Scale, RIMS tube, Plate Chiller, Chugger Pump, Super Clear Silicone Tubing, and more!

New Stuff?
Bobby_M is offline
 
Reply With Quote Quick reply to this message
Old 03-09-2007, 11:49 AM   #3
LouT
Can't wait to go AG...
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
LouT's Avatar
Recipes 
 
Join Date: Jan 2007
Location: Reading, MA
Posts: 863
Liked 1 Times on 1 Posts

Default

That is NICE sirsloop, thanks for the ideas.
I used a much larger piece of plywood, hoping I won't also need to use angle iron.
I really like the tips you gave on rail hardware - mine's ordered up, but I ordered the two sizes longer than you did for side rails, want to see what I think looks better on the top of kegerator before I drill.
Is there a reason not to go all the way from rear to front with the side rails? I was thinking I'd come a lot further forward with my side rails. I know it's not how the store-bought kegerators are set up, but this is CUSTOM... I just would like to know if I'm overlooking something and will regret going longer later.

__________________

Primary - California Common -finally!
Secondary - nothing, back after year plus hiatus
Keg carbing & conditioning - nada
Drinking - store bought: Loose Cannon IPA, Wachusett IPA.
On deck: Trying to decide (beer); wine kit likely (red wine)
LouT is offline
 
Reply With Quote Quick reply to this message
Old 03-09-2007, 12:42 PM   #4
homebrewer_99
Feedback Score: 0 reviews
 
homebrewer_99's Avatar
Recipes 
 
Join Date: Feb 2005
Location: Atkinson (near the Quad Cities), IL
Posts: 17,951
Liked 82 Times on 72 Posts
Likes Given: 1

Default

I like the railings idea, but would really like them to be over 4 " tall as I use mugs and taller weizen glasses.

__________________
HB Bill
homebrewer_99 is offline
 
Reply With Quote Quick reply to this message
Old 03-09-2007, 01:15 PM   #5
sirsloop
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2006
Location: South River, NJ
Posts: 2,592
Liked 16 Times on 15 Posts
Likes Given: 1

Default

You're on your own there

Really all you need is their rails, plus custom vertical pieces. They have thread on the top that goes into the horizontal piece, and 8-32 thread on the bottom for mount. Any machine shop could make those in a few minutes...

I put them on mainly for looks, but it will be nice when I have my wedding... keep plastic cups on there.

__________________
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ~~~~~~
~~~~~~~~~~~___//_ ____________________________~~~~~~~~~~~
~~~~~~~~~_/ [][]| | /```\/```\/```\/```\/```\ |~~~~~~~~~~
~~~~~~~_/_______| |____NOW TRIPLE HOPPED______|~~~~~~~~~~
~~~___/[_]| 00 /| | \,,,/\,,,/\,,,/\,,,/\,,,/ |~~~~~~~~~~
~~|___|___|___/_| |___________________________|~~~~~~~~~~
~~|=(*)[________]==(*)(*)=| \________/=(*)(*)=|~~~~~~~~~~

Last edited by sirsloop; 03-09-2007 at 01:18 PM.
sirsloop is offline
 
Reply With Quote Quick reply to this message
Old 03-09-2007, 01:41 PM   #6
homebrewer_99
Feedback Score: 0 reviews
 
homebrewer_99's Avatar
Recipes 
 
Join Date: Feb 2005
Location: Atkinson (near the Quad Cities), IL
Posts: 17,951
Liked 82 Times on 72 Posts
Likes Given: 1

Default

Oh, I agree they make the top look SHARP!

I would like my railings higher that's all.

__________________
HB Bill
homebrewer_99 is offline
 
Reply With Quote Quick reply to this message
Old 03-09-2007, 02:25 PM   #7
Ol' Grog
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2006
Location: Chickasha, OK.
Posts: 1,037
Liked 2 Times on 2 Posts

Default

Nice job, looks really neat.

__________________
Ol' Grog is offline
 
Reply With Quote Quick reply to this message
Old 03-09-2007, 08:46 PM   #8
LouT
Can't wait to go AG...
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
LouT's Avatar
Recipes 
 
Join Date: Jan 2007
Location: Reading, MA
Posts: 863
Liked 1 Times on 1 Posts

Default

My rails came today. Having tried both lengths for the sides, the one that goes from front to back all the way looks best to me.
So, the 19 7/32" (488mm) one fits the back
The 15 7/16" ones fit the sides from back to front (with a reasonable small gap between them and the rear rail.
These fit just inside of the "lip" around the perimeter of the 4912 plastic top.

I screwed up because I was at home dump and didn't remember what size screws and fender washers I needed (also didn't know that the UPS package was waiting at home). So it'll be another trip, if I have time later.

HB-99 -- if you really want taller rails, decide how much taller. Then you can just order an extra handle, cut it in half, and probably drill and tap the internal threads yourself but hire out a machine shop to do the external threads. If you go too tall, though, you'll want to reinforce the underside of the plastic - or side pressure on the rails will cause you to break the plastic (leverage effect).

BTW, the cost for the rails (I bought two extras so overpaid by about $14.00) was $47.20 including shipping. so if you just buy the ones you need you get out for about $33.00 and it really is a nice finished look that complements the brushed stainless tower in my opinion.

If I ever crack the plastic top, I'm going to do one in wood, with a thick urethane finish - maybe it'd be cool to cover it with a skin of stainless or galvanized sheet metal...
OK , getting out of hand now, I'll stop.

__________________

Primary - California Common -finally!
Secondary - nothing, back after year plus hiatus
Keg carbing & conditioning - nada
Drinking - store bought: Loose Cannon IPA, Wachusett IPA.
On deck: Trying to decide (beer); wine kit likely (red wine)
LouT is offline
 
Reply With Quote Quick reply to this message
Old 03-10-2007, 12:32 PM   #9
LouT
Can't wait to go AG...
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
LouT's Avatar
Recipes 
 
Join Date: Jan 2007
Location: Reading, MA
Posts: 863
Liked 1 Times on 1 Posts

Default

Well, I took the rails out of the packages, and placed them up there in mounting position, this time with drip tray in place. The shorter ones actually look better on the sides , so instead of the 15 7/16" rails, I'm going to use the 12 29/32 (328mm) ones for the side rails.
Hope to get it done today. We have family visiting, so I'm on it early.

__________________

Primary - California Common -finally!
Secondary - nothing, back after year plus hiatus
Keg carbing & conditioning - nada
Drinking - store bought: Loose Cannon IPA, Wachusett IPA.
On deck: Trying to decide (beer); wine kit likely (red wine)
LouT is offline
 
Reply With Quote Quick reply to this message
Old 03-10-2007, 02:55 PM   #10
Tony
Feedback Score: 0 reviews
 
Tony's Avatar
Recipes 
 
Join Date: Feb 2005
Location: Saugus, MA
Posts: 917
Liked 2 Times on 2 Posts

Default

From simple, humble beginnings...the compact Sanyo 4912 entered into existence to help keep food and drinks cool, and take up little space...a simple little fridge...

And now, the Sanyo mini fridges are ever evolving into little beer masters. Everyone just keeps coming up with more and more ideas.

Great job!

__________________
Up Next: Cherry Chocolate Rye
Up Next: Gold Nugget IPA
On Tap:Pawtucket Patriot
Dead Soldier:Hop Rod Rye Stout
Dead Soldier: Imperial Hell Fire Ale
Tony is offline
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Tower for Sanyo 4912 StankAle Equipment/Sanitation 24 01-23-2011 06:44 PM
Stainless steel 4 tap tower mysteryberto DIY Projects 8 10-13-2008 05:02 AM
kegconnection tower kit and sanyo 4912 quixotic Bottling/Kegging 1 09-22-2008 07:50 PM
4912 draft tower extension 8string Bottling/Kegging 6 03-13-2008 07:00 PM
Pics of another successful 4912 Tower Install =D Jekster Home Brewing Photo Forum 8 01-03-2008 05:20 PM