Ss Brewing Technologies Giveaway!

Home Brew Forums > Home Brewing Beer > Bottling/Kegging > Post pins push out past top after new seals?
Reply
 
LinkBack Thread Tools
Old 01-25-2013, 01:48 AM   #1
biohaz7331
Brew Addict
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
biohaz7331's Avatar
Recipes 
 
Join Date: Aug 2012
Posts: 294
Liked 11 Times on 11 Posts
Likes Given: 7

Default Post pins push out past top after new seals?

Sorry if this has already been addressed but I could not find anything specific to my question. Okay so whenever I buy used kegs I get the used keg seal kit that comes with all new seals. Whenever I disassemble the liquid side ports and put new seals with keg lube on them, the center portion sticks up higher than the rest of the port. I.E. instead of the center pin being flush with the whole port like it is when I get the keg, it sticks up past it. If no one understands what I am talking about I can post a picture. My question is, is this normal when putting new seals on a keg?

__________________
biohaz7331 is offline
 
Reply With Quote Quick reply to this message
Old 01-25-2013, 02:37 AM   #2
JuanMoore
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
JuanMoore's Avatar
Recipes 
 
Join Date: Oct 2009
Location: The Old Pueblo
Posts: 16,362
Liked 3217 Times on 3120 Posts
Likes Given: 18

Default

Are you referring to the poppet valves? If so, that's not normal IMO.

__________________
Keezer Soze

Yuri rubs it out with 60 grit... wouldn't even feel a tenga egg. -Randar

, place entry ox dixla to suck. Fcxk fwnpoo and passed. Hel an my spupid ass. OK. - TXCrash
JuanMoore is offline
 
Reply With Quote Quick reply to this message
Old 01-25-2013, 10:09 PM   #3
biohaz7331
Brew Addict
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
biohaz7331's Avatar
Recipes 
 
Join Date: Aug 2012
Posts: 294
Liked 11 Times on 11 Posts
Likes Given: 7

Default

Yes I am referring to the poppet. I was pretty sure that it was okay but when I bought them it was not sticking out past which led me to be slightly concerned. Thanks for the info!

__________________
biohaz7331 is offline
 
Reply With Quote Quick reply to this message
Old 01-25-2013, 11:54 PM   #4
shelly_belly
Locomotive Breath
HBT_SUPPORTER.png
Feedback Score: 1 reviews
 
shelly_belly's Avatar
Recipes 
 
Join Date: Jul 2009
Location: Rabbittown, Bama
Posts: 1,470
Liked 118 Times on 93 Posts
Likes Given: 19

Default

Your seals/gaskets/o-rings may be too thick.

__________________
shelly_belly is offline
 
Reply With Quote Quick reply to this message
Old 01-27-2013, 01:47 AM   #5
biohaz7331
Brew Addict
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
biohaz7331's Avatar
Recipes 
 
Join Date: Aug 2012
Posts: 294
Liked 11 Times on 11 Posts
Likes Given: 7

Default

I believe that they are actually smaller than the original seals because if they were thicker then the keg posts would be flush. Also when I took the old ones out they were wider but very square instead of round like a new seal. Every keg I have bought so far has had square shaped seals in them, but I believe these are just old seals that have become very worn out with age.

__________________
biohaz7331 is offline
 
Reply With Quote Quick reply to this message
Old 01-27-2013, 01:08 PM   #6
shelly_belly
Locomotive Breath
HBT_SUPPORTER.png
Feedback Score: 1 reviews
 
shelly_belly's Avatar
Recipes 
 
Join Date: Jul 2009
Location: Rabbittown, Bama
Posts: 1,470
Liked 118 Times on 93 Posts
Likes Given: 19

Default

The poppet legs will sit on the dip tube. The higher the dip tube is off of it's mating surface, the higher the poppet will be in the post. I observed this when I tried to use too thick of an o-ring on the dip tube. Another thing I can think of is that the dip tube may not be completely seated. Some of mine have a raised spot and have to be turned the correct way to seat completely. Also, it could be possible that the poppet legs are bent in to far making it stand taller. Or, your keg may have 2 different size poppets and they got switched. Or the top flange of your dip tube is bent down and not perpendicular to the tube. I've also seen a few poppets that the rubber was so worn that they would travel farther through the post hole before stopping. Good luck!

__________________
shelly_belly is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
For Sale - Pin lock post sets w/ poppets & new seals $10 each mrbippers For Sale 7 04-18-2012 06:12 PM
cut the pins off a corny keg? bloodonblood DIY Projects 10 02-08-2012 12:34 AM
Source for used pins? Teacher Bottling/Kegging 8 07-19-2009 06:10 PM
Balls vs. Pins Igorstien Bottling/Kegging 4 02-14-2006 02:30 AM