jonp9576

Recipes 

go i got my new tower. i found a good deal on it on craigs list.



i started taking it apart and realized a few things.

the faucets are plastic. is this going to be an issue?




the fittings where the beer line goes into the shank are like none i have ever seen. has anyone seen these? where can i get more of the black rubber pieces?




the lines used are much smaller than the line i am using now. is this an issue? should i make the smaller ID lines longer or shorter than my larger id lines i am running now?




finally, there was a copper pipe running into and out of the tower. i assume this is to keep the tower cold. can i do this, or should i just put a fan at the bottom of the tower to blow up cold air from the keezer?

__________________
On Tap:warrior apa
On Tap: crystal light
On Tap:BM's centenial blonde
"Just remember that the real enemy here are those wine drinking pussies."-BierMuncher

jonp9576

Recipes 

and where are my pictures?

__________________
On Tap:warrior apa
On Tap: crystal light
On Tap:BM's centenial blonde
"Just remember that the real enemy here are those wine drinking pussies."-BierMuncher

jonp9576

Recipes 

this is a link to an album with a bunch of pictures of the tower
Homebrew pictures from friends & fun photos on webshots

__________________
On Tap:warrior apa
On Tap: crystal light
On Tap:BM's centenial blonde
"Just remember that the real enemy here are those wine drinking pussies."-BierMuncher

jonp9576

Recipes 

anybody???

__________________
On Tap:warrior apa
On Tap: crystal light
On Tap:BM's centenial blonde
"Just remember that the real enemy here are those wine drinking pussies."-BierMuncher

ivanavich

Recipes 

that thing is beautifull. No clue on your question though.

MoRoToRiUm

Recipes 

If they are in good shape and not scratched, I'd say they're usable. I would look at replacing them personally (PERLICKS!)


No clue- Check out local hardware store or restaurant supply place maybe? If you change faucets, maybe re-do the shank setup? Not quite sure how they're in there...


Depends on your shanks- 3/16 is about normal. Any idea what size they are? They might be an issue... Short lines, no kinks, and no part above the taps... Maybe doable?


I actually have a piece of copper tubing I twisted around my lines in an effort to help keep them cooler; It helps, but blower would be beneficiary.


I say make a mold of it and make your own.. Haha ok a little ambitious. Good luck! Not much help, sorry

drunkatuw

Recipes 

The plastic faucet looks like a wine faucet - http://www.northernbrewer.com/pics/fullsize/plastic-faucet.jpg

Search Results

__________________
On tap: Amarillo Pale Ale, Impromptu Wit
Kegged: Sterling Gold (x2), Impromptu Wit, Lady Liberty cream ale (x2), Chinook SMaSH
Primary: Schwartzbier
Secondary:
On Deck: Barleywine

jonp9576

Recipes 

the only problem with replacing the shanks is that they are only about 1/2 inch compared to the 1'' that seem to be pretty standard. other faucets fit right on the shanks. i would love to find black perlicks. are they made anywhere? anyone wanna trade for some perlicks.


whats the big deal about perlicks any way. i am kind of new to all of this.


as far as the fitting on the end of the shank, if i boil the rubber gasket in there, or sanitize it in some solution, would it be safe to use? or should i seriously try to find new ones.

__________________
On Tap:warrior apa
On Tap: crystal light
On Tap:BM's centenial blonde
"Just remember that the real enemy here are those wine drinking pussies."-BierMuncher