WVBeerBaron

Recipes 

Hey Everybody!

I am changing my kegerator to handle corny kegs. I have four corny's, a 5lb CO2 tank, and a regulator. I was wondering what everyone's opinions was:

Is having the option to set different pressures important enough to buy a multi-pressure regulator or should I save money and buy a distribution bar/manifold???

I am also considering buying a new 20lb CO2 tank so I don't have to refill as often.

thanks for any help.

__________________
PRIMARY: Apple/Amber Ale
2NDARY: Infected Strawberry Blond
BOTTLED: Quad, ESB, Kriek, Hoppy Honey Nut Brown, Oaked Imperial Stout, Sierra Nevada PA
KEGGED: Barleywine & Saison
CONTEMPLATING: ??
The elusive Beer Baron continues to thumb his nose at the authorities. Swaggering about in a garish new hat, he seemed to say "Look at me, Rex Banner! I have a new hat!" - The Simpsons

Walker

Recipes 

I have never been bothered by carbing and serving all of my beers at the same pressure. I als was a cheap-skate and didn't even buy a manifold. I just bought a few plastic T-shaped hosebarbs and split my gas line into a spider.

__________________
Ground Fault Brewing Co.
Proud member of the GRABASS Brewing Disorganization
Help me give childhood cancer the middle finger and donate to the St. Baldrick's Foundation.
If everybody here gave just $1, it would rattle the walls in a big way.

Pubwilson

Recipes 

Here's my two pints. I recently bought a 20# tank and I have 3 cornies, and looking at running six eventually in my kegerator. My pipeline is up an running, so my plan is to run natural carbing in kegs versus force carbonation unless a special event calls for the beer to be ready sooner. I am going with a way distributor and saving some money beacause I will only be using my air for serving. If you are lookin to force carbonate (tank only) then you might want to look into multiple regulators to get the carb levels to style.
I have done natural carbing in my last three kegs and things have been great, except one belgium IPA was a little under carbed which I then used some gas to get it where is was supposed to be.
To the answer you were looking for, I feel that you should carb in the keg using the appropriate amount of sugars, then use your air distributor to serve at your preferred serving psi (mine is 9-11 psi). Your new 20# tank will last a really long time.
Just my two pints...

__________________
"I am a homebrewer, and I approve this homebrew!"
MOD EDIT: Your sig shouldn't be the largest text on the page.
Alamo Stew's Homebrews

BigTexun

Recipes 

Ditto what all above said. I put tees in my gas lines... and, being the cheapskate that I am, I have picnic taps on all kegs that say inside the fridge.

For force carbing, I first refrigerate the keg to be carbed. Disconnect the kegs not to be carbed.. and attach the uncarbed one. I then crank the pressure up to 30 psi and shake that sucker. After doing this a few times, that keg will be pretty close to fully carbed. Then, I lower the pressure and hook it all up.

Well, that's what I'm planning to do anyway. :-)

david_42

Recipes 

I run three pressures: soda (#35), regular (#12) and "real" (#2). Don't like my Bitters and Milds carbonated much, but flat IPAs are nasty.

__________________
Remember one unassailable statistic, as explained by the late, great George Carlin: "Just think of how stupid the average person is, and then realize half of them are even stupider!"

Bobby_M

Recipes 

Multi-pressure is a luxury. You can get away without it. You can also start with a few TEEs on the line for now and upgrade later if you think you want more carbonation variety later.

__________________
BrewHardware.com
Sightglass, Refractometer, Ball Valve, Weldless bulkhead, Thermometer, Decals, Stainless Steel Fittings, Compression Fittings, Camlock Quick Disconnects, Scale, RIMS tube, Plate Chiller, Chugger Pump, Super Clear Silicone Tubing, and more!

Personal Website, All Grain Primer, Keg Polishing, etc... | Youtube Channel