Come enter the BrewHardware Giveaway!


Home Brew Forums > Home Brewing Beer > Bottling/Kegging > leaking keg..
Reply
 
LinkBack Thread Tools
Old 05-22-2006, 07:06 PM   #1
revrand65
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2006
Location: ohio
Posts: 73
Default leaking keg..

i bought used cornie kegs and they were under pressure when i recieved them...cleaned them up installed new o rings except for the lid...and the lid leaks a little with the soapy water test at 10 psi..and it leaks pretty good at 5 psi...at 20 it doesn't leak at all i am useing lube on the o ring....the o ring is like new what pressure should i be running to serve my beer maybe i need to tighten the clamp?....or should i just run the pressure high...

__________________
revrand65 is offline
 
Reply With Quote Quick reply to this message
Old 05-22-2006, 07:33 PM   #2
david_42
Feedback Score: 0 reviews
 
david_42's Avatar
Recipes 
 
Join Date: Oct 2005
Location: Willamina & Oak Grove, Oregon, USA
Posts: 25,666
Liked 139 Times on 132 Posts

Default

First, check the o-ring. If there is any flattening, replace it. Rub it with a damp finger, if you get anything coming off, replace it. If you have to keep pressure on the lid to prevent leaks, the ring is probably old & too hard.

Frequently you can run the pressure up to seal the O-ring, then serve at a lower pressure. If you force carbonate at 30 psi, that should set the ring.

__________________

Remember one unassailable statistic, as explained by the late, great George Carlin: "Just think of how stupid the average person is, and then realize half of them are even stupider!"

"I would like to die on Mars, just not on impact." Elon Musk

david_42 is offline
 
Reply With Quote Quick reply to this message
Old 05-26-2006, 07:49 AM   #3
revrand65
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2006
Location: ohio
Posts: 73
Default

thanks for the advice..i ended up replaceing the rubber caps on the clamp and bending them a little and it seals just fine now..

__________________
revrand65 is offline
 
Reply With Quote Quick reply to this message
Old 05-26-2006, 07:49 AM   #4
revrand65
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2006
Location: ohio
Posts: 73
Default

thanks for the advice..i ended up replaceing the rubber caps on the clamp and bending them a little and it seals just fine now..

__________________
revrand65 is offline
 
Reply With Quote Quick reply to this message
Old 04-24-2012, 06:44 PM   #5
Dmatson89
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2012
Location: Metamora, IL
Posts: 53
Default

I am having the same problem with a keg i just bought. I too replaced the O-rings and even the lid one. However, I can not get the tank to seal now. It was holding pressure when it came in the mail but now leaks like a sieve. Is there any trick to getting it to seal, I am using keg lube on this one and never have before, could this have anything to do with it? If i cant get it to hold pressure I'll just send it back but really don't feel like paying $12 or so for return shipping.

__________________
Dmatson89 is offline
 
Reply With Quote Quick reply to this message
Old 04-25-2012, 12:58 AM   #6
Toymaker
Arrgh!
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
Toymaker's Avatar
Recipes 
 
Join Date: Feb 2012
Location: Livonia, Michigan
Posts: 140
Liked 18 Times on 12 Posts
Likes Given: 7

Default

Seal it under higher than serving pressure then turn it down. I also don't flip the bale down until it is sealed. I lube it good then lift up on the keg with the bale and swivel it around a bit to seat properly. Once sealed snap the bale down and you should be good to go!

__________________

Cheers,
Gary

Toymaker is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Might be leaking CO2? ahitz3 Bottling/Kegging 4 09-03-2009 12:55 AM
Keg Leaking...need some help. Hellfire_studios Bottling/Kegging 3 08-13-2009 12:02 AM
Keg Leaking!! RedOctober Beginners Beer Brewing Forum 11 12-02-2008 08:57 PM
CO2 is leaking...need help Atl300zx Equipment/Sanitation 12 10-18-2007 12:37 PM



Newest Threads

LATEST SPONSOR DEALS