*Ss Brewing Technologies Giveaway - Enter Now!*

Home Brew Forums > Home Brewing Beer > Bottling/Kegging > Considering a kegerator - crossposting in DIY
Reply
 
LinkBack Thread Tools
Old 02-07-2010, 09:40 PM   #1
Odnetni
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2010
Location: Maryland
Posts: 8
Default Considering a kegerator - crossposting in DIY

>Obligatory first post nonsense<

Hi! I'm starting to look at building myself a kegerator. Ideally I'd be able to fit one corny inside to begin with and have room for another down the road.

So I'm wondering what dimensions would be required. The fridge I've considered picking up from craigslist to start with is 18x18.5x32.5 - externally. The picture shows a freezer compartment, removable shelving, and some obtrusions from the plastic body. Can I remove things like the freezer compartment and plastic 'shell' and still expect the fridge to function correctly?

Lastly - and I haven't done much reading on the subject yet, so forgive me if this comes off as a silly question - but is a co2 tank normally held inside the body, or externally, connected through another hole drilled in the side?

Actually, probably the easiest way to ask what I want to know, is 'What dimensions do I need to look for in a minifridge to fit two corny kegs and the appropriate co2 tank?'
So thanks for your time. I love this place - it's great to be part of a community that shares knowledge so freely and willingly. Thanks!

__________________
Odnetni is offline
 
Reply With Quote Quick reply to this message
Old 02-09-2010, 08:30 PM   #2
RichBenn
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2009
Location: Tahoe
Posts: 748
Liked 13 Times on 12 Posts
Likes Given: 9

Default

Quote:
Originally Posted by Odnetni View Post
>Obligatory first post nonsense<

Hi! I'm starting to look at building myself a kegerator. Ideally I'd be able to fit one corny inside to begin with and have room for another down the road.

So I'm wondering what dimensions would be required. The fridge I've considered picking up from craigslist to start with is 18x18.5x32.5 - externally. The picture shows a freezer compartment, removable shelving, and some obtrusions from the plastic body. Can I remove things like the freezer compartment and plastic 'shell' and still expect the fridge to function correctly?
Pin Lock Kegs are "about" 22-23" X9" diameter, but the conectors are big, and add a couple of inches. It varies, depending upon manufacturer.

Ball Lock Kegs are "about" 26" X8.5" diameter, and the connectors are smaller. Again, it varies.

Most mini fridges inside don't quite make it due to height constraints. You need exact measurements, unless it's one of the tall inside min-fridges that is sought after for kegerator conversions(like a Sanyo 4912?). You can't remove the freezer in most, as the cooler refrigerant goes through the freezer bottom, but there are some who have bent the crap out of them without breaking them and ruining the fridge.

I'd look seriously at a chest freezer. You turn it all the way down, then add a temperature controller to keep it at the 38F or so. Very low power consumption (pays for itself), lot's of space, and good temperature regulation.

Quote:
Originally Posted by Odnetni View Post
>
Lastly - and I haven't done much reading on the subject yet, so forgive me if this comes off as a silly question - but is a co2 tank normally held inside the body, or externally, connected through another hole drilled in the side?
You can do it either way. Drilling through anything, you need to be sure you know exactly where the coolant goes. But check the exact dimensions of the CO2 tank AND the regulator. They vary somewhat, as well. You might get a 5 lb inside the mini-fridge with a big mini-fridge, but it'll be close.

Finally, read the sticky for making a kegerator. That'll get your juices flowing!

Rich
__________________
RichBenn is offline
 
Reply With Quote Quick reply to this message
Old 02-09-2010, 08:42 PM   #3
Crave
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2009
Location: Spokane, WA
Posts: 20
Default

Along with Sanyo 4912's, You can fit two ball-lock corny's in one of these:

http://www.homebrewtalk.com/f51/frig...version-89013/

__________________
Crave is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
For Sale - WTB or RENT 2 corny keg kegerator kit/kegerator Skacorica For Sale 0 01-27-2010 04:52 PM
Best Kegerator jamesjensen1068 Bottling/Kegging 8 01-21-2010 04:34 PM
Convert Conventional Kegerator to Cornelius Kegerator aschafer324 Bottling/Kegging 3 07-23-2009 10:12 PM
Ease of Going from Sanke Kegerator to Homebrew Kegerator polamalu43 Bottling/Kegging 6 04-28-2008 10:52 PM