*Ss Brewing Technologies Giveaway - Enter Now!*

Home Brew Forums > Home Brewing Beer > Bottling/Kegging > Any issues with caps that look like this?
Reply
 
LinkBack Thread Tools
Old 07-07-2013, 04:46 PM   #1
Doliss
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2013
Location: Leesburg, Virginia
Posts: 59
Liked 3 Times on 3 Posts

Default Any issues with caps that look like this?

I noticed after capping that the caps themselves had a small circular dent in the center from the capper. Pulling the handles down to cap the bottles was simple but I notice a bit of resistance as I lift the handles and take the capper off the bottles. Seems like this dent is from the center of the capper pushing to bottle out. Is this normal or do I have a faulty capper?

image-1845227467.jpg   image-1594842448.jpg  
__________________
Doliss is offline
 
Reply With Quote Quick reply to this message
Old 07-07-2013, 04:53 PM   #2
drainbamage
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
drainbamage's Avatar
Recipes 
 
Join Date: Oct 2011
Location: Alexandria, KY
Posts: 2,025
Liked 457 Times on 292 Posts
Likes Given: 844

Default

Mine does it occasionally. You have a standard wing capper, I take it?

While I don't think it's necessarily a bad thing to have the dent, my capper has been getting more stubborn over the last few batches. Either it doesn't seem to get a good seal, it takes too much effort to get the cap on properly, or in a couple of cases, it has gripped too hard and snapped the neck of the bottle. I'm probably going to phase it out for a bench capper soon.

__________________
drainbamage is offline
 
Reply With Quote Quick reply to this message
Old 07-07-2013, 05:03 PM   #3
Doliss
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2013
Location: Leesburg, Virginia
Posts: 59
Liked 3 Times on 3 Posts

Default

Yep, wing capper. Small center post when the capper is open shows up in the picture

image-3823139125.jpg   image-4116347136.jpg  
__________________
Doliss is offline
 
Reply With Quote Quick reply to this message
Old 07-07-2013, 05:30 PM   #4
drainbamage
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
drainbamage's Avatar
Recipes 
 
Join Date: Oct 2011
Location: Alexandria, KY
Posts: 2,025
Liked 457 Times on 292 Posts
Likes Given: 844

Default

Yeah, that's the same one I've got. Normally that center post with the magnet holds onto the cap and presses it against the neck of the bottle. But, if you pull the handles down too hard, the neck of the bottle gets caught in the capper and as you open it, the post comes back down and leaves that depression behind. Again, I don't think the dent will do anything to hurt your seal, it's just a matter of applying just the right amount of pressure to get a good seal on your cap without getting it caught in the capper.

__________________
drainbamage is offline
 
Reply With Quote Quick reply to this message
Old 07-07-2013, 05:49 PM   #5
Doliss
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2013
Location: Leesburg, Virginia
Posts: 59
Liked 3 Times on 3 Posts

Default

That must be it, I was pulling down pretty much all the way when seating the caps, guess i'll play with it and give a bit less pressure to see if there's a happy median. Thanks for the advice

__________________
Doliss is offline
 
Reply With Quote Quick reply to this message
Old 07-08-2013, 01:48 PM   #6
ChuckO
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
ChuckO's Avatar
Recipes 
 
Join Date: Oct 2008
Location: Keyrock, WV
Posts: 902
Liked 79 Times on 71 Posts
Likes Given: 13

Default

My old bench capper leaves a dent also if I press too hard on the lever. The shaft goes through the bell and is then peened over. I have never had a problem with bad seals yet.

__________________
ChuckO is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Oxygen absorbing caps vs standard caps Cajun_Tiger33 Bottling/Kegging 6 09-24-2012 05:40 PM
Re-using caps? Caucasian Bottling/Kegging 2 06-14-2012 03:21 PM
For Sale - Price Check! Possibly Selling Back Issues Lot: 89 Zymurgy Issues and more... bopgun23 For Sale 9 07-22-2011 12:36 AM
Caps Canadabrew Beginners Beer Brewing Forum 1 11-18-2010 03:03 AM
Old caps, and VERRY old caps sterling214 Bottling/Kegging 1 07-10-2008 06:01 PM