Happy HolidaySs Giveaway - Winners Re-Re-Re-Re-Re-Drawn - 24 hours to Claim!

Get your HBT Growlers, Shirts and Membership before the Rush!


Home Brew Forums > Home Brewing Beer > Bottling/Kegging > Air fittings and measuring
Reply
 
LinkBack Thread Tools
Old 01-21-2013, 06:41 PM   #1
rob211
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2012
Location: Oakland, CA
Posts: 22
Liked 2 Times on 1 Posts

Default Air fittings and measuring

I'm trying to figure out this whole air fittings thing. I know the difference between male and female flare fittings (eg MFL) and pipe fittings (NPT, MPT) but I'm having trouble with sizing.

If I go to buy say a short section of pipe to attach to a CO2 line, what size do I use?

I see 1/4" listed all the time, but I have no idea what that references, and I'd like to know. Ditto with thread pitch. And the flare angle; is it constant for the size of the fitting?

It seems that the conventions are different in the brewing world vs the welding world (in welding I see tanks measured in cu ft, in brewing it's lbs).

Also, I have tons of fittings laying around for air hoses for air tools. They all are 1/4", both flare and pipe. I also have quick disconnects for 1/4" both auto and industrial (one is slightly longer than the other IIRC). I'd like to use some of these with my CO2 system for the keezer, and I don't wanna go buy stuff only to have it prove incompatible. And I need to use the CO2 tank with other stuff.

__________________
rob211 is offline
 
Reply With Quote Quick reply to this message
Old 01-21-2013, 09:22 PM   #2
beaksnbeer
HBT_LIFETIMESUPPORTER.png
Feedback Score: 1 reviews
 
beaksnbeer's Avatar
Recipes 
 
Join Date: May 2011
Location: New Port Richey, Florida
Posts: 2,827
Liked 492 Times on 326 Posts
Likes Given: 67

Default

You can use the air line connectors for your LOW pressure sides most here do not because of the cost and the fact that they are big and bulky. The high side of your regulator should be rated for at LEAST 1200psi for CO2 and 4000psi for Nitrogen. The air line Quick Disconnects should be 1/4 npt and thread into the low pressure ports without a problem, I use a crap load of these at work and they do leak which when running off a compressor that is constantly putting out 100+psi is not a problem BUT when you have a limited gas supply ANY leak is a tank killer. Bottom line I have at least 2 dozen of these fitting and I would never use them. I am currently changing all my low pressure gas lines over to John Guest fittings (aka. push-lock) as I like the sealing quality and the ease of change out. Then again this is just my opinion you my have better luck.

__________________
Quote:
Home of the 12 Tap keezer
beaksnbeer is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Weldless Fittings vs. Welded Fittings for Keggles Stevorino Equipment/Sanitation 42 10-29-2012 12:07 PM
welded fittings to weldless fittings ElevenBrewCo Equipment/Sanitation 7 11-16-2011 12:36 PM
For Sale - bulkhead fittings and swagelock elbows fittings agroff383 For Sale 7 06-18-2011 11:30 PM
Sold - Brass fittings: Ball valves / Mash tun fittings doobliebop For Sale 6 03-01-2010 04:02 AM



Newest Threads

LATEST SPONSOR DEALS