Get your HBT Growlers, Shirts and Membership before the Rush!


Home Brew Forums > Home Brewing Beer > DIY Projects > Fermenters > A/C Thermostat Wiring?
Reply
 
LinkBack Thread Tools
Old 05-16-2010, 07:10 PM   #1
czucker
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2008
Posts: 73
Default A/C Thermostat Wiring?

Hi,
I'm getting started on my fermentation cabinet and could use some help with the A/C wiring.

I have an old window unit that I was hoping had the screw type temp control that Jamil mentioned on one of the Brew Strong podcasts.

Sadly, that's not the case. I pulled it apart and found a Ranco PCB in there.

Does anyone know how to rewire this to run at colder temps?

Here is an image of the PCB.



Thanks,
Chris

__________________
czucker is offline
 
Reply With Quote Quick reply to this message
Old 05-16-2010, 07:18 PM   #2
whoneedsabeer
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2009
Location: Wilmington, DE
Posts: 196
Default

Why not just get a Johnson controller and be done with it? I would think it would be a lot easier, and if you screw up your wiring, you might trash your whole AC unit.

__________________
whoneedsabeer is offline
 
Reply With Quote Quick reply to this message
Old 05-16-2010, 07:22 PM   #3
czucker
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2008
Posts: 73
Default

I am eventually going to have it hooked up to a FermTroller.

That's not really my issue at the moment. I am trying to figure out how to get the unit to run colder than the 60 degree (or comething around there) lower temperature limit.

__________________
czucker is offline
 
Reply With Quote Quick reply to this message
Old 05-16-2010, 09:55 PM   #4
samc
Feedback Score: 1 reviews
Recipes 
 
Join Date: Aug 2008
Location: Portland OR
Posts: 5,420
Liked 55 Times on 52 Posts
Likes Given: 29

Default

You could wrap the probe in enough insulation to fool it into thinking it's warmer then it is. Trial and error. Used to do that with my oven for pizza baking, which is a bit tricky but it worked.

__________________
samc is offline
 
Reply With Quote Quick reply to this message
Old 05-16-2010, 10:47 PM   #5
JewBrew
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2010
Location: Brooklyn, NY
Posts: 175
Liked 2 Times on 2 Posts
Likes Given: 1

Default

Build this.http://suburb.semo.net/jet1024/Controller.htm I made this to control a glycol jacketed fermentation thingy

__________________
JewBrew is offline
 
Reply With Quote Quick reply to this message
Old 05-17-2010, 04:32 AM   #6
kladue
Senior Member
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2006
Location: Turner, Oregon, Oregon most of the time now
Posts: 2,309
Liked 47 Times on 43 Posts

Default

If there is enough wire slack cut the sensor wires long enough to wire nut/solder back together. Test the sensors to see what the resistance is between leads and if as I suspect ranco used 10K@70 Deg F thermistors, you can install 22K ohm resistors across the sensor leads to shift operaing point down to 30's. This will change the span on the slide control but it will be a set and leave alone situation probably as the old scale span will not be the same as altered scale span. If the reading is different PM me with reading and temperature and I can calculate a shunt resistor value for you.

__________________
kladue is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Wiring up Freezer with LOVE bypassing Thermostat Only IrregularPulse Equipment/Sanitation 8 03-13-2013 04:49 PM
Thermostat wiring bytemyfoot Kegerators and Keezers 2 12-05-2009 04:35 PM
Thermostat wiring help HopShepard Fermenters 5 05-28-2009 02:02 AM
NEW CL Freezer, need thermostat wiring info balto charlie Fermenters 4 02-18-2008 01:14 AM
Thermostat? Nexus555 Equipment/Sanitation 4 03-13-2007 02:17 AM



Newest Threads

LATEST SPONSOR DEALS