Home Brew Forums > Home Brewing Beer > DIY Projects > Kettles, Mash Tuns, & Hot Liquor Tanks > Sanke Keg - hole drilled slightly too big, need advice
Reply
 
LinkBack Thread Tools
Old 09-01-2009, 03:04 AM   #1
bmickey
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2009
Location: NE Ohio
Posts: 190
Default Sanke Keg - hole drilled slightly too big, need advice

I had ordered this Blichmann Brewmometer beforehand thinking I was going to get a Polarware kettle with a threaded insert BUT then I got a Keg instead and tried to make this work. I can't get a good seal because the hole was drilled slightly too big I think and now I'm trying to get washers and o-rings to fill the gap.

My question is these threads are 1/2" NPT. I'm tightening this into a copper 1/2" coupler inside. On McMaster Carr they have stainless steel (18-8 or 316) with washer sizes like .5,.501,.503,.515,.531, etc.
McMaster-Carr

What would you guys say would be a tight fit but fit over the threads. I will use a washer or two on the outside and inside plus some o-rings around 11/32size to hopefully seal this up for good.

Thinking bout these O-Rings:
McMaster-Carr

Any thoughts?

Here is the temp probe I have.


As always I appreciate the help!

__________________

bmickey is offline
 
Reply With Quote Quick reply to this message
Old 09-01-2009, 03:52 AM   #2
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
Vendor Ads 
Feedback Score: 3 reviews
 
Bobby_M's Avatar
Recipes 
 
Join Date: Aug 2006
Location: Whitehouse Station, NJ
Posts: 22,364
Liked 1112 Times on 738 Posts
Likes Given: 28

Default

If you have a Lowes near you, they have stainless washers in the specialty drawers. Get the 3/4" ones. However, you will probably find that you have to pack the heck out of the threads with teflon tape to get it to seal because orings don't seal against threads. Instead of washers, you might want to go with a locknut on the thermo, sealed to the threads with teflon, and backed all the way down.

The Oring you're looking at is way too small. You'd want something like an ASTM number 313. You can probably do it cheaper by getting some silicone baby bottle nipples and use the mounting ring with the nipple cut off.

__________________
BrewHardware.com has a new website. Please check it out and let me know what you think!
New 100% Stainless Steel Heating Elements are IN!
Chugger Pumps, Pump Kits, Camlocks, Sightglasses, Clear USA made Silicone Tubing, RIMS, Electric Install Parts, etc. Did you know we are also now a full service homebrew shop selling malt, hops, yeast (Wyeast), etc?
Bobby_M is online now
 
Reply With Quote Quick reply to this message
Old 09-01-2009, 04:30 AM   #3
JVD_X
HBT_LIFETIMESUPPORTER.png
Feedback Score: 4 reviews
 
JVD_X's Avatar
Recipes 
 
Join Date: Jan 2008
Location: Gainesville, Virginia
Posts: 1,492
Liked 3 Times on 3 Posts

Default

Yea - drill out to 3/4" and use a reducer coupling like this one then just order the right o-rings...

__________________

- JVD_X

JVD_X is offline
 
Reply With Quote Quick reply to this message
Old 09-01-2009, 12:39 PM   #4
bmickey
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2009
Location: NE Ohio
Posts: 190
Default

Ok so 3/4" washers should fit snug?

The normal locknut with nylon threads is rated above boiling temps so maybe I'll try that. Thanks guys!

__________________
bmickey is offline
 
Reply With Quote Quick reply to this message
Old 09-01-2009, 05:02 PM   #5
Simphoto02
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2009
Location: Louisville, KY
Posts: 451
Liked 1 Times on 1 Posts

Default

Contact your local Homebrew shop or club. Ask them if anybody in the shop or club TIG welds stainless.

I found a guy here that welded my 3 keggles for the ball valve, temp fitting (same one you have there) and the sighttube for 10.00 a fitting IF i supplied the fittings and predrilled the holes.

__________________

HOOKED!!!!!!!!!!!!

Got tired of waiting for our savior to save the economy, so I jumped into all grain, What the hell!!!

Simphoto02 is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Hole in mash tun need advice ddrayne10 All Grain & Partial Mash Brewing 4 11-03-2009 01:34 AM
For Sale - Two 15 gal Megapots, drilled WormBoy For Sale 8 08-02-2009 06:52 PM
I may have drilled the keggle hole too big mramann Kettles, Mash Tuns, & Hot Liquor Tanks 19 02-11-2009 09:47 PM
Cleaning burned sanke kegs - any advice? sdsurf Equipment/Sanitation 16 12-22-2008 11:43 PM
Drilled my keggle... Funkenjaeger Kettles, Mash Tuns, & Hot Liquor Tanks 19 05-14-2008 07:35 PM



Newest Threads

LATEST SPONSOR DEALS