Happy HolidaySs Giveaway - Last Sponsor Giveaway of the Year!

Come Enter the BrewDeals/FastFerment Giveaway!


Home Brew Forums > Home Brewing Beer > DIY Projects > Chillers and Stir Plates > New immersion chiller
Reply
 
LinkBack Thread Tools
Old 02-16-2009, 07:47 PM   #1
ghack
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
ghack's Avatar
Recipes 
 
Join Date: Dec 2008
Location: New Orleans
Posts: 266
Liked 8 Times on 8 Posts

Default New immersion chiller

Finished this up this weekend. It just needs a cleaning and a boil, and it’s ready to go. I decide to upgrade my old 20' coil of 1/4" tubing. I had a leftover 10' length, dismantled my first attempt at a semi-counterflow and sometimes pre-chiller for another 10’ and added 20' more.

So I now have 60’ of tubing held in two coils in a 1/2” copper frame.



I will be looking to get a pump to recirculate ice water once the domestic water gets to it’s normal 75 to 80 degrees in the summer.

I kept the height fairly low, as I typically do five gallon batches. But it should work fine for ten gallons. The center coil sits about two inches higher than the outer. The diameter allows it to fit in a standard five gallon bucket for cleaning and storage.

The support arms are standard 1/2” plumbing copper and fitting. I took the idea of drilling the supports from keelanfish’s design in the thread http://www.homebrewtalk.com/f51/imme...1/#post1069585, which is tad more elaborate than I had the inclination for. Only the two supports are drilled to support the bottom and top, and I added a handle to carry it without grabbing the actual tubing.



The lowest cross-bar sits on the side of the domed bottom of my keggle and leaves a pretty good gap. If it encounters too much of the hot break, I’ll add some kind of feet to lift it up a little.

__________________
ghack is offline
 
Reply With Quote Quick reply to this message
Old 02-16-2009, 08:46 PM   #2
Notnice
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2009
Location: Ft. Lauderdale
Posts: 254
Liked 2 Times on 2 Posts

Default

Wow verry nice. I think I may have to coppy youre design when I put together mine

__________________
Morrison's Brew House

Priming: CBB 1.1, apfelwein
Chillin:1st Mead, ApfelMango-Cyzer, aleApfelwein,blackchapfelwein,blackfelwein,
Blucyzer, Cyzer.
Bottled: Apfelwein 2, Crazy Beech Bitter
Trench Town Brown, Mouf of the Souf Stout, New Mouf of the Souf, Oaked Apfel, Slow-wit
Next Up:Cream ale, Scott red, 888RIS or cocoOatmealRIS, Apfelwein and more Apfelwein

"Always do sober what you said you would do drunk. That will teach you to keep you're mouth shut."-E. Hemingway
Notnice is offline
 
Reply With Quote Quick reply to this message
Old 02-16-2009, 09:03 PM   #3
keelanfish
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2008
Location: Decatur, GA
Posts: 318
Liked 4 Times on 2 Posts

Default

Well done. I like the use of the tees to simplify my idea of drilling all the holes in the support pipes. Let us know how it performs!

__________________
keelanfish is offline
 
Reply With Quote Quick reply to this message
Old 02-16-2009, 09:06 PM   #4
jonp9576
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2008
Location: Lansdale, PA
Posts: 1,348
Liked 3 Times on 3 Posts
Likes Given: 1

Default

love the 2 coils and the support system with handle. i will definately be loking at this again when i make my chiller

__________________

On Tap:warrior apa
On Tap: crystal light
On Tap:BM's centenial blonde
"Just remember that the real enemy here are those wine drinking pussies."-BierMuncher

jonp9576 is offline
 
Reply With Quote Quick reply to this message
Old 02-16-2009, 09:26 PM   #5
MoRoToRiUm
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2008
Posts: 1,413
Liked 4 Times on 4 Posts

Default

Man that's a lot of copper... Well done! Love the design! I'm almost as anxious as you to see how it works- Happy brewing!

__________________
Broken Face Brewery
Est. 2008
MoRoToRiUm is offline
 
Reply With Quote Quick reply to this message
Old 02-16-2009, 11:14 PM   #6
Jewrican
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2008
Location: GA
Posts: 895
Liked 5 Times on 4 Posts
Likes Given: 10

Default

how much did it cost you for the whole project?

__________________
JewRican Brew Works
Jewrican is offline
 
Reply With Quote Quick reply to this message
Old 02-16-2009, 11:34 PM   #7
ghack
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
ghack's Avatar
Recipes 
 
Join Date: Dec 2008
Location: New Orleans
Posts: 266
Liked 8 Times on 8 Posts

Default

Cost is a tough to figure because I already had 40' of the tubing, and the 2 to 3 feet of 1/2" pipe and elbows were leftover from some plumbing work on my house.

All told I spent about $35 for 20' feet of tube, the compression fittings and copper T's and coupling for the tubing.

The tubing is most of it. I think all the fittings and 1/2" pipe would run about $20 total.

__________________
ghack is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Help With Immersion Chiller? JrZyBud Equipment/Sanitation 7 01-29-2012 09:02 PM
immersion chiller zurcj20 Chillers and Stir Plates 3 09-29-2009 12:18 AM
immersion Chiller Skins_Brew Beginners Beer Brewing Forum 5 02-25-2008 11:09 PM
Immersion Chiller JimiGibbs Beginners Beer Brewing Forum 3 03-17-2006 05:24 AM



Newest Threads

LATEST SPONSOR DEALS