Get your HBT Growlers, Shirts and Membership before the Rush!


Home Brew Forums > Home Brewing Beer > DIY Projects > Brew Stands > Valve-Orifice from Brewers Hardware Question
Reply
 
LinkBack Thread Tools
Old 04-11-2012, 09:41 PM   #1
bbentley40
Feedback Score: 0 reviews
Recipes 
 
Join Date: Oct 2008
Location: Madison, AL
Posts: 174
Liked 3 Times on 3 Posts
Likes Given: 1

Default Valve-Orifice from Brewers Hardware Question

Ok.. so I am trying to piece together what all I need to start plumbing my brewstand and I have a question for those that might know. Does the valve/orifice linked below act as a low pressure orifice and a needle valve to control the flame or would I need it an a needle value to fine tune things?

http://www.brewershardware.com/Valve...or-BURN10.html

Thanks guys!

__________________

Bentley

My Keezer Build

bbentley40 is offline
 
Reply With Quote Quick reply to this message
Old 04-12-2012, 06:55 AM   #2
OneHoppyGuy
HBT_SUPPORTER.png
HomeBrewTalk 2012 Vendor Giveaway Participate
Feedback Score: 0 reviews
 
OneHoppyGuy's Avatar
Recipes 
 
Join Date: Nov 2009
Location: Concord, CA
Posts: 1,704
Liked 40 Times on 33 Posts
Likes Given: 52

Default

it is a low pressure orifice/needle valve all in one

__________________

Brewright. All Rights Reserved. We reserve the right to brew and to help you brew. To protect the brew and defend the brew. To make the brew and drink the brew.

BrewSteel.com
BrewSteel on Facebook

OneHoppyGuy is offline
 
Reply With Quote Quick reply to this message
Old 04-12-2012, 12:17 PM   #3
beardedirishman
Feedback Score: 0 reviews
Recipes 
 
Join Date: Oct 2010
Location: knoxville, tennessee
Posts: 44
Liked 5 Times on 4 Posts

Default

It's actually a ball valve i believe, but it does control flame size pretty well. I have one on each of my burners, and they're pretty easy to adjust to dial in my flame.

__________________
beardedirishman is offline
 
Reply With Quote Quick reply to this message
Old 04-12-2012, 03:20 PM   #4
bbentley40
Feedback Score: 0 reviews
Recipes 
 
Join Date: Oct 2008
Location: Madison, AL
Posts: 174
Liked 3 Times on 3 Posts
Likes Given: 1

Default

Quote:
Originally Posted by beardedirishman View Post
It's actually a ball valve i believe, but it does control flame size pretty well. I have one on each of my burners, and they're pretty easy to adjust to dial in my flame.
So you dont use needle valves at all, just the orifice/valve setup to tune the flame? Just trying to figure out if I need to buy needle valves too so I can start buying up the parts I need... and based on the two posts above I guess I can skip the separate needle valves. Thanks guys.
__________________

Bentley

My Keezer Build

bbentley40 is offline
 
Reply With Quote Quick reply to this message
Old 04-12-2012, 03:51 PM   #5
phoenixs4r
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2011
Location: Hayward, California
Posts: 1,515
Liked 55 Times on 50 Posts
Likes Given: 38

Default

Quote:
Originally Posted by bbentley40

So you dont use needle valves at all, just the orifice/valve setup to tune the flame? Just trying to figure out if I need to buy needle valves too so I can start buying up the parts I need... and based on the two posts above I guess I can skip the separate needle valves. Thanks guys.
You do not need to get needle valves as well. I have the same valve on my NG set up and control the flame perfectly from that orifice/valve you linked. Its gets kind warm, as it screws directly into the burner, but not that bad.
__________________
phoenixs4r is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Spunding Valve - Pressure relief valve part question kpr121 Fermenters 3 05-14-2012 02:28 PM
Correct wiring of Brewers Hardware Temp Probe to BCS HungusBrews Brew Stands 16 01-18-2012 04:10 PM
Brewers Hardware bulkhead CoalCracker Kettles, Mash Tuns, & Hot Liquor Tanks 3 09-21-2011 09:26 PM
Opinions On Ball Valve, Gate Valve, Or Globe Valve For March Pumps jcav Brew Stands 13 10-16-2010 04:56 AM
high pressure orifice wolfe006 Brew Stands 5 05-15-2009 01:28 PM



Newest Threads

LATEST SPONSOR DEALS