Happy HolidaySs Giveaway - Winners Re-Re-Re-Re-Drawn - 24 hours to Claim!

Get your HBT Growlers, Shirts and Membership before the Rush!


Home Brew Forums > Home Brewing Beer > DIY Projects > Brew Stands > Programming TS2 Love Control
Reply
 
LinkBack Thread Tools
Old 01-28-2009, 01:35 PM   #1
brewboy5150
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2008
Location: New Hampshire
Posts: 19
Liked 1 Times on 1 Posts

Default Programming TS2 Love Control

I am have a heck of a time programming my TS2 switch. The sheet that comes with the unit is useless. Any tips on how to do this. I want a heating element to come on when the temp hits 66 and go off when it gets to 69.

__________________
brewboy5150 is offline
 
Reply With Quote Quick reply to this message
Old 01-28-2009, 02:06 PM   #2
MNBugeater
Feedback Score: 0 reviews
 
MNBugeater's Avatar
Recipes 
 
Join Date: Jan 2006
Location: Minneapolis, MN
Posts: 979
Liked 7 Times on 5 Posts

Default

Set to heat mode.
Set Point to 68
Differential to 1 degree

That will get you close, if your set point is 68 with a diff of 1. When the temp drops to 66, it will close the circuit and delivery power. When the temp hits 70 the circuit will open and remove power. You would think that when it hits your set point it would close the circuit, but it is still within the 1 degree differential, so until the reading gets outside that differential it wont close/open the switch.

Edit: Here are the parameters you want and the programming seqeunce

• Press SET for 8 seconds. The access code value
00 is shown on the display. (Unit comes with
code set at 00 from factory).
• With the UP and DOWN arrows, code can be set to
user needs.
• Press SET to enter the code. If it is correct, the first
parameter label is shown on the display (SP).
• Move to the desired parameter with the UP and
DOWN keys.
• Press SET to view the value on the display.
• The value can be modified with the UP and DOWN
arrows.
• Press SET to enter the value and exit to test
parameter.
• Press SET and DOWN at the same time to quit
programming or wait one minute and the display will
automatically exit programming mode.

You want the following parameters.
d0 = Ht
r0 = 1

It may appear that you want to set the Upper and Lower set point limits based on what you want it to do, but the limit parameters just control or 'limit' the range of your high and low setting. They basically act as fail-safes in the event you didnt want to allow it to be set too high or too low. I set mine on my keezer just so that little kids or drunk adults dont start pushing buttons on it and freeze my beer. But it isnt necessary.

__________________

On Tap: Blonde Ale, Apfelwein, Cinnamon Apfelwein, Amber Ale, Irish Red
Bottled: Porter, Wheat, Barleywine, Cranberry Apfelwein, Amber Ale
Buy Bugeater Brewery Gear


MNBugeater is offline
 
Reply With Quote Quick reply to this message
Old 01-28-2009, 02:11 PM   #3
brewboy5150
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2008
Location: New Hampshire
Posts: 19
Liked 1 Times on 1 Posts

Default

Thanks. That helps. I was not sure if I should set the Low and High Set point or the Differential.

__________________
brewboy5150 is offline
 
Reply With Quote Quick reply to this message
Old 01-28-2009, 02:20 PM   #4
MNBugeater
Feedback Score: 0 reviews
 
MNBugeater's Avatar
Recipes 
 
Join Date: Jan 2006
Location: Minneapolis, MN
Posts: 979
Liked 7 Times on 5 Posts

Default

Think of the differential as setting the span or range of temperature before the switch turns on/off and the limit points to be your potential minimum and maximum limits and you should be good.

__________________

On Tap: Blonde Ale, Apfelwein, Cinnamon Apfelwein, Amber Ale, Irish Red
Bottled: Porter, Wheat, Barleywine, Cranberry Apfelwein, Amber Ale
Buy Bugeater Brewery Gear

MNBugeater is offline
 
Reply With Quote Quick reply to this message
Old 11-06-2009, 05:09 AM   #5
GamePreserve
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2009
Location: Philadelphia
Posts: 69
Liked 2 Times on 2 Posts
Likes Given: 2

Default

what is r0, r1? lower and higher set points?

__________________
GamePreserve is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
LOVE TSS2-2100 Programming help dunleav1 Equipment/Sanitation 18 04-16-2012 12:40 AM
help with Love TS programming GamePreserve Kegerators and Keezers 17 12-24-2009 06:00 PM
Love TS2-010 temp control brewboy5150 Fermenters 21 01-26-2009 06:10 PM
Love control help? Battery_BreweryNJ Equipment/Sanitation 9 07-13-2008 01:35 AM



Newest Threads

LATEST SPONSOR DEALS