Come enter the BrewHardware Giveaway!


Home Brew Forums > Home Brewing Beer > DIY Projects > Brew Stands > My single tier LPG/eRIMS build
Reply
 
LinkBack Thread Tools
Old 04-26-2012, 05:09 AM   #21
rossi46
Senior Member
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
rossi46's Avatar
Recipes 
 
Join Date: Jan 2011
Location: Pasco, WA
Posts: 749
Liked 50 Times on 40 Posts
Likes Given: 5

Default

Quote:
Originally Posted by fxdude
Looking great
Thanks. Just need more time to work on it.
__________________
rossi46 is offline
 
Reply With Quote Quick reply to this message
Old 04-29-2012, 06:12 PM   #22
rossi46
Senior Member
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
rossi46's Avatar
Recipes 
 
Join Date: Jan 2011
Location: Pasco, WA
Posts: 749
Liked 50 Times on 40 Posts
Likes Given: 5

Default

Got the burners mounted. Adjustable height, 2,3,and 4 inches.
Can't find the right gas fittings I want here in town, I'll have to find some on the net somewhere. 3/8 female flare to 1/4 male pipe for the orifice to needle valve.

image-3405369775.jpg  
__________________
rossi46 is offline
 
Reply With Quote Quick reply to this message
Old 04-30-2012, 01:51 AM   #23
rossi46
Senior Member
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
rossi46's Avatar
Recipes 
 
Join Date: Jan 2011
Location: Pasco, WA
Posts: 749
Liked 50 Times on 40 Posts
Likes Given: 5

Default

Got my very simple pump shields made today.

image-3153063050.jpg  
__________________
rossi46 is offline
 
Reply With Quote Quick reply to this message
Old 04-30-2012, 01:57 AM   #24
Kylito87
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2010
Location: Chicago, Illinois
Posts: 64
Liked 1 Times on 1 Posts

Default

Nice clean brew rig . Also the bike Can't go wrong with a springer front end!!!!

__________________
Kylito87 is offline
 
Reply With Quote Quick reply to this message
Old 04-30-2012, 02:41 AM   #25
StainlessBrewing
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
StainlessBrewing's Avatar
Recipes 
 
Join Date: Sep 2009
Location: Gilbert, AZ
Posts: 845
Liked 82 Times on 70 Posts
Likes Given: 137

Default

This setup is looking good! Was it a tough decision trying to figure out if you want to put the pumps above or below the tube? Once you get the connectors on they look like they're going to be pretty low.

__________________
Stainless Brewing LLC
Equipment, fittings, valves, tubing, accessories, kegging, custom fabrication and more.
Stainless is Painless at www.stainlessbrewing.com
StainlessBrewing is offline
 
Reply With Quote Quick reply to this message
Old 04-30-2012, 03:22 AM   #26
rossi46
Senior Member
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
rossi46's Avatar
Recipes 
 
Join Date: Jan 2011
Location: Pasco, WA
Posts: 749
Liked 50 Times on 40 Posts
Likes Given: 5

Default

I knew I wanted them under because the rims and chiller, also the shields would be super easy to make.
The inlet will be about 10"

image-240272977.jpg  
__________________
rossi46 is offline
 
Reply With Quote Quick reply to this message
Old 04-30-2012, 03:50 AM   #27
StainlessBrewing
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
StainlessBrewing's Avatar
Recipes 
 
Join Date: Sep 2009
Location: Gilbert, AZ
Posts: 845
Liked 82 Times on 70 Posts
Likes Given: 137

Default

Plenty! It looks a lot lower in the other picture.

__________________
Stainless Brewing LLC
Equipment, fittings, valves, tubing, accessories, kegging, custom fabrication and more.
Stainless is Painless at www.stainlessbrewing.com
StainlessBrewing is offline
 
Reply With Quote Quick reply to this message
Old 04-30-2012, 11:17 AM   #28
Dougie63
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2011
Location: St Petersburg, FL
Posts: 272
Liked 6 Times on 5 Posts
Likes Given: 1

Default

on the shields you need to put a 30 deg angle on each side cradling the pump because when they are flat and liquid drips on them it can flow under and damage pumps

__________________
Dougie63 is offline
 
Reply With Quote Quick reply to this message
Old 04-30-2012, 02:47 PM   #29
rossi46
Senior Member
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
rossi46's Avatar
Recipes 
 
Join Date: Jan 2011
Location: Pasco, WA
Posts: 749
Liked 50 Times on 40 Posts
Likes Given: 5

Default

Ok, thanks Dougie

__________________
rossi46 is offline
 
Reply With Quote Quick reply to this message
Old 05-04-2012, 04:57 AM   #30
rossi46
Senior Member
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
rossi46's Avatar
Recipes 
 
Join Date: Jan 2011
Location: Pasco, WA
Posts: 749
Liked 50 Times on 40 Posts
Likes Given: 5

Default

Got my control panel pieces put in, still need to wire. Waiting on some gas plumbing parts and a couple of ball valves.

image-1573618477.jpg   image-228459122.jpg   image-1174198893.jpg  
__________________
rossi46 is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools




Newest Threads

LATEST SPONSOR DEALS