Happy HolidaySs Giveaway - Last Sponsor Giveaway of the Year!

Come Enter the BrewDeals/FastFerment Giveaway!


Home Brew Forums > Home Brewing Beer > DIY Projects > Brew Stands > Any tips on installing a 1500 watt element?
Reply
 
LinkBack Thread Tools
Old 05-07-2010, 12:27 PM   #1
BrewBarron
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2010
Location: Omaha
Posts: 88
Liked 1 Times on 1 Posts

Default Any tips on installing a 1500 watt element?

I am having a few issues installing a 1500 watt element inside my round cooler. I have tried installing it a few different ways (rubber gasket on the inside, gasket on the outside) but I still end up springing a leak. Any tips on getting a good seal with the element and a 1 inch nut? Once I get a good seal I will protect the wiring with a pvc sleave and JB weld it together.

Also, I have seen these set ups built with a home-made copper washer and some without. Can anyone tell me if this copper washer/ground is necessary in this set up, or not?

thanks for your help.

__________________
BrewBarron is offline
 
Reply With Quote Quick reply to this message
Old 05-07-2010, 01:21 PM   #2
lustreking
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2006
Location: Bethlehem, PA
Posts: 750
Liked 18 Times on 17 Posts
Likes Given: 7

Default

I used the big stainless locknut on the inside of the cooler, with a rubber washer between the cooler and the element. The locknut has a grooved side and a flat side. I made sure the flat side was facing the cooler.

For a ground, I drilled a hole and tapped one of the flanges on the element. after attaching the ground with a machine screw, I filled in the hole on the other (sealing) side with JB Weld. I've used it a couple times without issue.

__________________

My brewing site:
http://brewing.lustreking.com

lustreking is offline
 
Reply With Quote Quick reply to this message
Old 05-07-2010, 02:08 PM   #3
passedpawn
Waste Allocation Load Lifter - Earth Class
HBT_MODERATOR.png
Feedback Score: 0 reviews
 
passedpawn's Avatar
Recipes 
 
Join Date: Apr 2009
Location: ☼ Clearwater, FL ☼
Posts: 19,617
Liked 3600 Times on 2221 Posts
Likes Given: 3104

Default

Your ground wire should make contact with the wort or hot water. Otherwise, if the conductor inside the element somehow comes in contact with the liquid, nothing will happen until YOU touch the liquid. With the liquid properly grounded, your breaker or GFCI will trip the instant the fault occurs.

__________________
Hey goomba I love how you dance the rumba
But take some advice paisano learn-a how to mambo
If you're gonna be a square you ain't-a gonna go anywhere.
passedpawn is offline
 
Reply With Quote Quick reply to this message
Old 05-08-2010, 03:21 AM   #4
BrewBarron
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2010
Location: Omaha
Posts: 88
Liked 1 Times on 1 Posts

Default

Thanks lustreking, passedpawn,

I drilled into the flange and installed a screw so that should take care of my ground. I'm still having problems getting a good seal with the element though. I bought the nut and rubber gasket from bargain fittings and have tried a number of combinations of installation, but the cooler still has a slow leak.

I'll keep trying. Thanks again for the advice.

__________________
BrewBarron is offline
 
Reply With Quote Quick reply to this message
Old 05-08-2010, 03:48 AM   #5
GreenMonti
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2009
Posts: 1,014
Liked 8 Times on 8 Posts

Default

Quote:
Originally Posted by BrewBarron View Post
Thanks lustreking, passedpawn,

I drilled into the flange and installed a screw so that should take care of my ground. I'm still having problems getting a good seal with the element though. I bought the nut and rubber gasket from bargain fittings and have tried a number of combinations of installation, but the cooler still has a slow leak.

I'll keep trying. Thanks again for the advice.
How tight are you trying to get it?

Just snug should be sufficient.
__________________
GreenMonti is offline
 
Reply With Quote Quick reply to this message
Old 05-08-2010, 01:25 PM   #6
BrewBarron
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2010
Location: Omaha
Posts: 88
Liked 1 Times on 1 Posts

Default

I am actually just hand tightening it. I have tried the rubber gasket in the grove on the nut on the inside of the cooler, I have tried the flatter side of the nut on the inside and a gasket on the outside, I think I have even tried a gasket on both sides, still no good seal.

????

__________________
BrewBarron is offline
 
Reply With Quote Quick reply to this message
Old 05-08-2010, 02:18 PM   #7
lustreking
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2006
Location: Bethlehem, PA
Posts: 750
Liked 18 Times on 17 Posts
Likes Given: 7

Default

I used a flat rubber washer that I found in the plumbing dept of Lowes, as opposed to an o-ring. I think that gives me a little more sealing surface.

__________________

My brewing site:
http://brewing.lustreking.com

lustreking is offline
 
Reply With Quote Quick reply to this message
Old 05-08-2010, 02:24 PM   #8
EvilGnome6
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2009
Location: Scottsdale, AZ
Posts: 678
Liked 9 Times on 9 Posts

Default

I had a slow leak in mine and fixed it by applying a thin coat of silicone aquarium sealant to the gasket and the contact areas on the cooler and element. Hasn't leaked a drop since.

__________________
musicgourmets.com
EvilGnome6 is offline
 
Reply With Quote Quick reply to this message
Old 05-08-2010, 06:51 PM   #9
rcrabb22
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
rcrabb22's Avatar
Recipes 
 
Join Date: Jun 2008
Location: Illinois
Posts: 734
Liked 21 Times on 15 Posts
Likes Given: 17

Default

Quote:
Originally Posted by BrewBarron View Post
I am actually just hand tightening it. I have tried the rubber gasket in the grove on the nut on the inside of the cooler, I have tried the flatter side of the nut on the inside and a gasket on the outside, I think I have even tried a gasket on both sides, still no good seal.

????
examine the hole you drilled for the element to make sure there are no small splits or cracks on the edge. I enlarged the drain hole on my 10 gal orange Rubbermaid for 1/2" nipple and did have a small irregularity that would not seal leak free. I used a step bit to clean the hole up slightly and now am leak free.
__________________
rcrabb22 is offline
 
Reply With Quote Quick reply to this message
Old 05-09-2010, 01:59 AM   #10
thorongil
HBT_SUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2007
Location: Buckeye, Arizona
Posts: 278
Liked 4 Times on 2 Posts
Likes Given: 1

Default

If all else fails, pick up some food-grade silicone sealant. I used it on my cooler and have never leaked a drop...

__________________
“Altogether 1420 in the Shire was a marvelous year... The Northfarthing barley was so fine that the beer of 1420 malt was long remembered and became a byword. Indeed a generation later one might hear an old gaffer in an inn, after a good pint of well-earned ale, put down his mug with a sigh: ‘Ah! that was a proper fourteen-twenty, that was!’”

- J.R.R. Tolkien, The Lord of the Rings, The Return of the King
thorongil is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
5500 watt ripp element pp270 Brew Stands 8 02-01-2010 04:00 AM
Best controller for a 4500 Watt Element hayabusa Brew Stands 26 03-25-2009 11:28 PM
control for 4500 watt element brewjunky Equipment/Sanitation 2 06-01-2008 04:05 AM
5500 watt element Brewpastor Equipment/Sanitation 18 03-20-2007 05:35 PM
1500 Watt Hotplate akira7799 Equipment/Sanitation 7 12-13-2005 06:01 AM



Newest Threads

LATEST SPONSOR DEALS