Home Brew Forums

Home Brew Forums (http://www.homebrewtalk.com/forum.php)
-   Kegerators and Keezers (http://www.homebrewtalk.com/f252/)
-   -   VISSANI Build (http://www.homebrewtalk.com/f252/vissani-build-383445/)

aarong 01-22-2013 12:41 AM

VISSANI Build
 
2 Attachment(s)

Here is a vissani build that I have just finished. I wanted to post instructions on how to DIY. It is a very clean looking fridge everything is self contained with no external boxes.

Here is the final product with the fridge closed. It is the front closed and a picture of the back. The outlet is split one is hot and one is for cold.

My inspiration was from Ingchr's vissani fermentation chamber

I wanted to build it using a STC 1000 but wanted to install it inside the fridge so you can read it through the glass


aarong 01-22-2013 12:41 AM

VISSANI Build
 
2 Attachment(s)

Here is a vissani build that I have just finished. I wanted to post instructions on how to DIY. It is a very clean looking fridge everything is self contained with no external boxes.

Here is the final product with the fridge closed. It is the front closed and a picture of the back. The outlet is split one is hot and one is for cold.

My inspiration was from Ingchr's vissani fermentation chamber

I wanted to build it using a STC 1000 but wanted to install it inside the fridge so you can read it through the glass


aarong 01-22-2013 01:04 AM

1 Attachment(s)

So for the build. I bought the vissani fridge for $70.00 which is way below the average cost it is normally in the low to mid $100.00 range on sale. I bought all my parts from Homedepot besides the STC 1000 from newegg.com

Part list:
STC 1000 $24.00
20' of 300V rubber power cord for $0.48/ft I got 20 feet
1 gang Outlet Box $2.74
100 W light bulb (at home)
15 AMP outlet $1.19
Empty paint can $2.97
Face plate $0.62
Black outlet plate $0.47
Hez nut 4mm-7hex $0.50
Standard screw (any old one will work around 1 inch)
15 A plug $2.97
Weatherproof socket for the light bulb $3.28
Machine screw 4mm-.7 x 20mm $0.96
White plug 15A $1.99
1 gang low voltage bracket $1.65

Total $53.00

Note there is extra pieces in the photo but you only need what is on the list


aarong 01-22-2013 01:18 AM

5 Attachment(s)

I am in no way an expert electrician or an expert in refridgeration. Conduct this build at your own risk. Have fun and be safe.
So here we go:

First I bypassed the thermostat according to Ingchr's post

2) Cut the tabs off the back of the 1 gang low voltage bracket this will allow it to fit perfectly under the built in thermostat control of the fridge(Pic1) Then clean up the side of the orange bracket. I used a box cutter

3) Cut a square the size of the STC panel in the solid face plate. This was the hardest part of the project for me. I used a box cutter to score it then I used anything I had to cut it out. I would recommend a dremel. (Pic 2)

4) Screw the face plate on the orange box with included screws. (Pic 3)

5) Remove the thermostat box/ light attachment on the top of the fridge. This is simply unscrewing two screws under the box. Pull down and toward you and it will come right off.

6)Unhook the light. Pull the white thermostat straight off and unscrew the thermometer. Remember where the wires where that you pulled off of the thermostat so you can put it back on. The whole black thermostat box will separate from the fridge. (Pic 4 5)


aarong 01-22-2013 01:18 AM

5 Attachment(s)

I am in no way an expert electrician or an expert in refridgeration. Conduct this build at your own risk. Have fun and be safe.
So here we go:

First I bypassed the thermostat according to Ingchr's post

2) Cut the tabs off the back of the 1 gang low voltage bracket this will allow it to fit perfectly under the built in thermostat control of the fridge(Pic1) Then clean up the side of the orange bracket. I used a box cutter

3) Cut a square the size of the STC panel in the solid face plate. This was the hardest part of the project for me. I used a box cutter to score it then I used anything I had to cut it out. I would recommend a dremel. (Pic 2)

4) Screw the face plate on the orange box with included screws. (Pic 3)

5) Remove the thermostat box/ light attachment on the top of the fridge. This is simply unscrewing two screws under the box. Pull down and toward you and it will come right off.

6)Unhook the light. Pull the white thermostat straight off and unscrew the thermometer. Remember where the wires where that you pulled off of the thermostat so you can put it back on. The whole black thermostat box will separate from the fridge. (Pic 4 5)


aarong 01-22-2013 01:18 AM

5 Attachment(s)

I am in no way an expert electrician or an expert in refridgeration. Conduct this build at your own risk. Have fun and be safe.
So here we go:

First I bypassed the thermostat according to Ingchr's post

2) Cut the tabs off the back of the 1 gang low voltage bracket this will allow it to fit perfectly under the built in thermostat control of the fridge(Pic1) Then clean up the side of the orange bracket. I used a box cutter

3) Cut a square the size of the STC panel in the solid face plate. This was the hardest part of the project for me. I used a box cutter to score it then I used anything I had to cut it out. I would recommend a dremel. (Pic 2)

4) Screw the face plate on the orange box with included screws. (Pic 3)

5) Remove the thermostat box/ light attachment on the top of the fridge. This is simply unscrewing two screws under the box. Pull down and toward you and it will come right off.

6)Unhook the light. Pull the white thermostat straight off and unscrew the thermometer. Remember where the wires where that you pulled off of the thermostat so you can put it back on. The whole black thermostat box will separate from the fridge. (Pic 4 5)


aarong 01-22-2013 01:18 AM

5 Attachment(s)

I am in no way an expert electrician or an expert in refridgeration. Conduct this build at your own risk. Have fun and be safe.
So here we go:

First I bypassed the thermostat according to Ingchr's post

2) Cut the tabs off the back of the 1 gang low voltage bracket this will allow it to fit perfectly under the built in thermostat control of the fridge(Pic1) Then clean up the side of the orange bracket. I used a box cutter

3) Cut a square the size of the STC panel in the solid face plate. This was the hardest part of the project for me. I used a box cutter to score it then I used anything I had to cut it out. I would recommend a dremel. (Pic 2)

4) Screw the face plate on the orange box with included screws. (Pic 3)

5) Remove the thermostat box/ light attachment on the top of the fridge. This is simply unscrewing two screws under the box. Pull down and toward you and it will come right off.

6)Unhook the light. Pull the white thermostat straight off and unscrew the thermometer. Remember where the wires where that you pulled off of the thermostat so you can put it back on. The whole black thermostat box will separate from the fridge. (Pic 4 5)


aarong 01-22-2013 01:18 AM

5 Attachment(s)

I am in no way an expert electrician or an expert in refridgeration. Conduct this build at your own risk. Have fun and be safe.
So here we go:

First I bypassed the thermostat according to Ingchr's post

2) Cut the tabs off the back of the 1 gang low voltage bracket this will allow it to fit perfectly under the built in thermostat control of the fridge(Pic1) Then clean up the side of the orange bracket. I used a box cutter

3) Cut a square the size of the STC panel in the solid face plate. This was the hardest part of the project for me. I used a box cutter to score it then I used anything I had to cut it out. I would recommend a dremel. (Pic 2)

4) Screw the face plate on the orange box with included screws. (Pic 3)

5) Remove the thermostat box/ light attachment on the top of the fridge. This is simply unscrewing two screws under the box. Pull down and toward you and it will come right off.

6)Unhook the light. Pull the white thermostat straight off and unscrew the thermometer. Remember where the wires where that you pulled off of the thermostat so you can put it back on. The whole black thermostat box will separate from the fridge. (Pic 4 5)


aarong 01-22-2013 01:40 AM

5 Attachment(s)

7) Now attach the orange 1 gang low voltage bracket to the black thermostat/ light box on the fridge. I drilled a whole straight down from the black thermostat/light to the orange box. Then place the machine screw straight threw the hole and put a little bit of crazy glue on the head of the screw. You will have to attach the black thermostat/ light box on the fridge before you attach the orange box. There will be two screw posts hanging under the thermostat and two holes on top of the orange box(Pic 6, 7)

8) After a few minutes push the orange box onto the studs from the machine screw. Use the nuts to attach it to the fridge(Pic 8)

9) Now comes the fun part wiring! Drill a few holes on top of the hump in the back left corner of the fridge. I drilled 3 holes in the fridge. Two wires ran from the back of the fridge to the orange box. One ran from the back of the fridge to where the paint can heater is(I will describe how to build this late). Leave extra wire(better to have too much then too little)

10) The first step to wiring is taking one of the cords and using a sharpie to label wires. I took one of the wires one of the whites will be (green cold) one of the green wires will be black.

11) The numbers on top of the diagram are the outputs for the STC 1000. The wires coming in from the bottom is the wire that is plugged into the wall outlet. The middle is the back of the outlet.


aarong 01-22-2013 01:40 AM

5 Attachment(s)

7) Now attach the orange 1 gang low voltage bracket to the black thermostat/ light box on the fridge. I drilled a whole straight down from the black thermostat/light to the orange box. Then place the machine screw straight threw the hole and put a little bit of crazy glue on the head of the screw. You will have to attach the black thermostat/ light box on the fridge before you attach the orange box. There will be two screw posts hanging under the thermostat and two holes on top of the orange box(Pic 6, 7)

8) After a few minutes push the orange box onto the studs from the machine screw. Use the nuts to attach it to the fridge(Pic 8)

9) Now comes the fun part wiring! Drill a few holes on top of the hump in the back left corner of the fridge. I drilled 3 holes in the fridge. Two wires ran from the back of the fridge to the orange box. One ran from the back of the fridge to where the paint can heater is(I will describe how to build this late). Leave extra wire(better to have too much then too little)

10) The first step to wiring is taking one of the cords and using a sharpie to label wires. I took one of the wires one of the whites will be (green cold) one of the green wires will be black.

11) The numbers on top of the diagram are the outputs for the STC 1000. The wires coming in from the bottom is the wire that is plugged into the wall outlet. The middle is the back of the outlet.



All times are GMT. The time now is 09:30 PM.

Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.