Happy HolidaySs Giveaway - Last Sponsor Giveaway of the Year!

Come Enter the BrewDeals/FastFerment Giveaway!


Home Brew Forums > Home Brewing Beer > DIY Projects > Kegerators and Keezers > Sanyo 4912 Kegerator Conversion
Reply
 
LinkBack Thread Tools
Old 01-14-2007, 05:48 AM   #1
John Beere
Deep Six Brewing Co.
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
John Beere's Avatar
Recipes 
 
Join Date: May 2006
Location: Valdosta, GA
Posts: 2,140
Liked 38 Times on 29 Posts
Likes Given: 5

Default Sanyo 4912 Kegerator Conversion

I know this has been covered by many but I'm doing a few things different that I haven't seen anyone else do (for better or worse) - so I thought I share...

First thing I did after throughly testing the fridge was take the inside of the door off to make more room. The screws are under the rubber seal and there are a LOT of them. There are also two different type screws so be careful to note which screws come out of which holes. Here is the plastic door insert after removing the rubber seal:



I then noted which side of the insert was the top and pulled out the dremel tool. From the back side of the insert, I began cutting the plastic right at the ridge all the way around and ended up with this:



I then cleaned it up a little, reinstalled the rubber seal, and screwed it all back together.

John Beere is offline
 
Reply With Quote Quick reply to this message
Old 01-14-2007, 05:57 AM   #2
John Beere
Deep Six Brewing Co.
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
John Beere's Avatar
Recipes 
 
Join Date: May 2006
Location: Valdosta, GA
Posts: 2,140
Liked 38 Times on 29 Posts
Likes Given: 5

Default

The next thing I did was to see how cold the fridge would go if I just turned it on "maximum". I don't know exactly how cold it will go b/c I stopped it at 26 degrees... this was good news because if "maximum" wouldn't go to at least freezing I was going to have to bypass the thermostat.

I then wired up a Ranco thermostat to the unit and mounted it in the rear next to the compressor.



By setting the fridge to "maximum" I can now completely control the temperature of the fridge all the way down to freezing if I want...

For the temperature probe, I did the exact same thing as my walk-in cooler and used a White Labs yeast container filled with the goop from a freezer pack. I pushed the probe through the drain plug into the fridge and mounted it at the very top as near to the front as I could. It is attached with two heavy zip ties.



Thats as far as I've gotten so far as my tower hasn't arrived yet... so it will be a few days before I get to drilling out the top.

John Beere is offline
 
Reply With Quote Quick reply to this message
Old 01-14-2007, 06:10 AM   #3
John Beere
Deep Six Brewing Co.
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
John Beere's Avatar
Recipes 
 
Join Date: May 2006
Location: Valdosta, GA
Posts: 2,140
Liked 38 Times on 29 Posts
Likes Given: 5

Default

A caveat to cutting the door out like I've done is that the light switch will not be depressed when the door is closed so the light will always be on. My solution was to just remove the bulb...

John Beere is offline
 
Reply With Quote Quick reply to this message
Old 01-16-2007, 03:37 PM   #4
John Beere
Deep Six Brewing Co.
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
John Beere's Avatar
Recipes 
 
Join Date: May 2006
Location: Valdosta, GA
Posts: 2,140
Liked 38 Times on 29 Posts
Likes Given: 5

Default

It seems Orpheus has just posted similar steps to add a tower to this same fridge - so to keep from being redundant on those steps, Click Here: http://www.homebrewtalk.com/showthread.php?t=19762

John Beere is offline
 
Reply With Quote Quick reply to this message
Old 01-16-2007, 04:58 PM   #5
aekdbbop
Feedback Score: 0 reviews
 
aekdbbop's Avatar
Recipes 
 
Join Date: Sep 2006
Location: Nashville, TN
Posts: 2,772
Liked 8 Times on 7 Posts

Default

nice man, i did the same with the door, only a little more crazy like. But after i was done ripping it up, i covered the insulation with black duct tape.. it was an easy thing to do that made it look a little nicer.

__________________
Bare Tree Brewing Co.
"Straight from the earth"


aekdbbop is offline
 
Reply With Quote Quick reply to this message
Old 01-16-2007, 05:02 PM   #6
aekdbbop
Feedback Score: 0 reviews
 
aekdbbop's Avatar
Recipes 
 
Join Date: Sep 2006
Location: Nashville, TN
Posts: 2,772
Liked 8 Times on 7 Posts

Default

Quote:
Originally Posted by John Beere
A caveat to cutting the door out like I've done is that the light switch will not be depressed when the door is closed so the light will always be on. My solution was to just remove the bulb...

ha i didnt even think about the bulb... it has been on for 4 days now.. oops.. yeah i just unscrewed it a little. when i need it to see, i can just turn it a bit to make it come back on...
__________________
Bare Tree Brewing Co.
"Straight from the earth"

aekdbbop is offline
 
Reply With Quote Quick reply to this message
Old 01-28-2007, 05:07 AM   #7
John Beere
Deep Six Brewing Co.
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
John Beere's Avatar
Recipes 
 
Join Date: May 2006
Location: Valdosta, GA
Posts: 2,140
Liked 38 Times on 29 Posts
Likes Given: 5

Default

I finally got around to finishing up my kegerator. I bought a taprite dual regulator (model #5754-wmhp-tay) off ebay. I quickly fashioned a mounting plate for it out of a piece of scrap metal and bent the metal so it would stand out about a 1/2".



__________________

Website: Deep Six Brewing Co.
Merchandise: http://zazzle.com/deepsix
Projects: HERMs Setup v2.0 | Fermentation Cabinets | Milling Station | Wort Chilling Station| Walk-in Cooler | Kegerator

"If thair is no gas bing pasted thru the air lock check for a leak."
"Handcrafted Brewing - A guide for All home brewers!" by Stan Richards, RFC - Copyright 1992.

John Beere is offline
 
Reply With Quote Quick reply to this message
Old 01-28-2007, 05:08 AM   #8
John Beere
Deep Six Brewing Co.
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
John Beere's Avatar
Recipes 
 
Join Date: May 2006
Location: Valdosta, GA
Posts: 2,140
Liked 38 Times on 29 Posts
Likes Given: 5

Default

I took the top two screws out of the cold plate in the back of the fridge and mounted the regulator to it.



Here it is hooked up to my 5 lb tank.



And finally, with the two kegs.



I'm dry running everything for tonight to check for leaks and hope to hook it up for the first time tomorrow!

__________________

Website: Deep Six Brewing Co.
Merchandise: http://zazzle.com/deepsix
Projects: HERMs Setup v2.0 | Fermentation Cabinets | Milling Station | Wort Chilling Station| Walk-in Cooler | Kegerator

"If thair is no gas bing pasted thru the air lock check for a leak."
"Handcrafted Brewing - A guide for All home brewers!" by Stan Richards, RFC - Copyright 1992.

John Beere is offline
 
Reply With Quote Quick reply to this message
Old 01-28-2007, 03:55 PM   #9
Tony
Feedback Score: 0 reviews
 
Tony's Avatar
Recipes 
 
Join Date: Feb 2005
Location: Saugus, MA
Posts: 917
Liked 2 Times on 2 Posts

Default

Looks great!

I have the same fridge, and back when I made mine, I removed the inner door of mine as well to make more room. I simply removed the gasket, then removed the door, then replaced the gasket. No plexiglass or anything, as since I figured the door is insulated enough, and I keep steady temps inside still.

I ran into the same problem concerning the light. I noticed that the inner door, of course, was what depressed the pin switch for the light. What I did was disassemble the control box, and unplugged and removed the switch. Different method, same results.

My curious question for everyone who has one of these, is what dial setting are you all having to set yours to, to get proper temps? I notice John Beere's is set to max to test, but have heard others having to set it the same for regular serving temps. I have mine set to near 3. If I set it to exactly 3 it gets down to 38. If I set it between 3 and 4, it gets down to 32. If i set it at 4 or more, it gets below 25.

Just wondering if I have a odd ball.

__________________
Up Next: Cherry Chocolate Rye
Up Next: Gold Nugget IPA
On Tap:Pawtucket Patriot
Dead Soldier:Hop Rod Rye Stout
Dead Soldier: Imperial Hell Fire Ale

Tony is offline
 
Reply With Quote Quick reply to this message
Old 01-28-2007, 04:51 PM   #10
John Beere
Deep Six Brewing Co.
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
John Beere's Avatar
Recipes 
 
Join Date: May 2006
Location: Valdosta, GA
Posts: 2,140
Liked 38 Times on 29 Posts
Likes Given: 5

Default

If you look back to post #2 you'll see that I added a Ranco temperature controller to the fridge to exactly regulate the temperature.

I got the fridge down to 26 degrees when I tested the max setting. Not sure how much colder it would have gone but it was still running when I stopped the test.

__________________

Website: Deep Six Brewing Co.
Merchandise: http://zazzle.com/deepsix
Projects: HERMs Setup v2.0 | Fermentation Cabinets | Milling Station | Wort Chilling Station| Walk-in Cooler | Kegerator

"If thair is no gas bing pasted thru the air lock check for a leak."
"Handcrafted Brewing - A guide for All home brewers!" by Stan Richards, RFC - Copyright 1992.

John Beere is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Sanyo 4912 Kegerator Conversion Orpheus Bottling/Kegging 144 05-01-2012 10:43 PM
Gearing a Sanyo 4912 For Kegerator Conversion amercuric Bottling/Kegging 2 07-02-2009 11:44 AM
5lb or 10lb for sanyo 4912 conversion? eb50 Equipment/Sanitation 10 05-23-2008 05:39 PM
Sanyo 4912 conversion ?? GIusedtoBe Bottling/Kegging 7 12-23-2007 04:41 AM
Sanyo 4912 Conversion Parts List Lepoc2635 Kegerators and Keezers 0 07-30-2007 02:34 PM



Newest Threads

LATEST SPONSOR DEALS