Happy HolidaySs Giveaway - Last Sponsor Giveaway of the Year!

Come Enter the BrewDeals/FastFerment Giveaway!


Home Brew Forums > Home Brewing Beer > Electric Brewing > Tapping a Triclamp cap ?
Reply
 
LinkBack Thread Tools
Old 12-23-2011, 05:04 AM   #1
joeybeer
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2009
Posts: 524
Liked 11 Times on 11 Posts
Likes Given: 27

Default Tapping a Triclamp cap ?

I wasn't really sure where to put this but since it involves my electric build I thought this was as good as anywhere..

Has anyone tapped a triclamp cap ?? I'd like to screw in a 1/2 NPT ball valve..
I know I could use a more expensive solution, but I'd like to install a heating element in one 2" cap and a 1/2" ball valve on another I thought I'd try this first..

I'd like to tap them so I can just screw them in, but I could also get nuts welded on a drilled hole, or use regular "weldless" bulkhead fittings..

What do y'all think ?

__________________
joeybeer is offline
 
Reply With Quote Quick reply to this message
Old 12-23-2011, 05:19 AM   #2
sv_1
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2011
Location: Concord, Ca
Posts: 67
Liked 1 Times on 1 Posts

Default

Brewers Hardware 2" Tri Clover X 1/2" Female NPT

vs

http://www.amazon.com/Quality-Speed-...bxgy_hi_text_b

and

http://www.amazon.com/Vermont-Americ.../dp/B000O9N072

Unless you have the tools already (including a drill press), I'd skip the headache and buy a ready made solution.
__________________
sv_1 is offline
 
Reply With Quote Quick reply to this message
Old 12-23-2011, 09:46 PM   #3
kevink
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2010
Location: PA
Posts: 509
Liked 48 Times on 38 Posts
Likes Given: 7

Default

Tapping will work fine for the element, but you can do a little better. I recommend welding on a 1" nps locknut like you mentioned because it has a groove in it that accepts a silicone o-ring. It keeps it from squeezing out when you tighten the element. It's totally the way to go. It makes for a very nice installation.

For the ball valve, either tapping or welding on a coupler will be fine. Weldless isn't as nice as either of the other options. I don't know if anyone even offers weldless "kits" for such a thick material. The end caps are close to 1/4". Even if they did, I would steer away from them.

__________________
kevink is offline
 
Reply With Quote Quick reply to this message
Old 12-23-2011, 10:36 PM   #4
Bsquared
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
Bsquared's Avatar
Recipes 
 
Join Date: Oct 2006
Location: San Diego
Posts: 1,813
Liked 56 Times on 51 Posts
Likes Given: 22

Default

Check this guys ebay site too, KLG Stainless If you dont find what you are looking for email him, he usually has a lot of stuff in stock that he dose not have listed. It might be a lot less hassle to get a fitting to do what you are thinking of doing. Unless you have access to a mill, or other metal machining equipment.

__________________
Bsquared is offline
 
Reply With Quote Quick reply to this message
Old 12-27-2011, 09:12 PM   #5
BigBobsBrews
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2010
Location: Indianapolis, IN
Posts: 158
Liked 5 Times on 5 Posts
Likes Given: 1

Default

Speaking form experience here, I'd just recommend buying the fittings (I also highly recommend KLG Stainless".

I tried tapping a cap as well, but ended up wasting an hour & destroying 2 taps in the process. They just weren't strong enough to tap through 1/4" stainless.

__________________
BigBobsBrews is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Triclamp heater element design TheFlyingBeer Electric Brewing 113 08-18-2013 01:55 AM



Newest Threads

LATEST SPONSOR DEALS