Get your HBT Growlers, Shirts and Membership before the Rush!


Home Brew Forums > Home Brewing Beer > Electric Brewing > Show us your element housings/pots. How did you do it?
Reply
 
LinkBack Thread Tools
Old 12-16-2010, 02:16 PM   #1
Boerderij_Kabouter
Feedback Score: 0 reviews
 
Boerderij_Kabouter's Avatar
Recipes 
 
Join Date: Dec 2007
Location: Oconomowoc, Wisconsin
Posts: 8,461
Liked 125 Times on 104 Posts
Likes Given: 11

Default Show us your element housings/pots. How did you do it?

I can't believe this thread doesn't exist. Let's put together a resource for people to see how they want to protect themselves for electrocution!

I'll go first...

My BK uses a rubber coated keg, so my situation may be a bit different.



It is a cannibalized plastic box with an all weather face plate. The recessed outlet is sealed up with silicone and the box is fully plastic welded (plastic specific epoxy) to the keg exterior.

I used a profile guage to steal the profile of the keg:



Then, I traced that profile onto the box, and cut it out with my mini band saw.

Then I clamped the box in place with a bungie cord, and epoxied the crap out of it. Wiped smooth with a squeegee and bob's yer uncle.



The flash picks up some extra epoxy, but it looks perfect with the naked eye.

Boerderij_Kabouter is offline
 
Reply With Quote Quick reply to this message
Old 12-16-2010, 02:34 PM   #2
Layne
HBT_SUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2008
Location: Gonzales, Louisiana
Posts: 964
Liked 19 Times on 17 Posts
Likes Given: 2

Default

You KNOW I'm ready to do mine, so I'll be watching this thread with interest.

__________________
Layne is offline
 
Reply With Quote Quick reply to this message
Old 12-16-2010, 03:06 PM   #3
ScubaSteve
Feedback Score: 0 reviews
 
ScubaSteve's Avatar
Recipes 
 
Join Date: May 2007
Location: New Bern, NC
Posts: 3,691
Liked 68 Times on 50 Posts
Likes Given: 11

Default

For my elements, I used 1" SLB conduit elbows, boring the hole a little larger with a step bit. Then I inserted the element, wired it up to include a strain relief at the bottom, and filled it with JB Weld. I let the epoxy cure overnight, not moving it until it hardened right where I wanted it. Then I screwed on the backplate and attached the ground wire to a lug I soldered on the kettle.

Just hope I don't burn out an element....it's more work than I'd want to do every few brews, but it's rock solid and as safe as I could make it.

p1040074.jpg   p1040087.jpg   p1040138.jpg  
ScubaSteve is offline
 
Reply With Quote Quick reply to this message
Old 12-16-2010, 03:44 PM   #4
stevehaun
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2006
Location: hudson, wi
Posts: 575
Liked 15 Times on 15 Posts
Likes Given: 26

Default

Sorry for the link but I have never figured out how to post pics here.
http://picasaweb.google.com/sehaun3333/ElectricalBox#
Too make a long story short, I had 1/4" ss bolts welded to my kettles and then bolted on a waterproof outlet box. I drilled a hole in the back big enough to go over the electric element coupling and then used silicone caulking to seal up.

__________________
stevehaun is offline
 
Reply With Quote Quick reply to this message
Old 12-16-2010, 03:46 PM   #5
Diver165
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
Diver165's Avatar
Recipes 
 
Join Date: May 2010
Location: Huntington, WVA
Posts: 532
Liked 11 Times on 9 Posts
Likes Given: 3

Default

Yes awesome thread. Im getting ready to go electric and I need tips and advice

__________________
Diver165 is offline
 
Reply With Quote Quick reply to this message
Old 12-16-2010, 08:43 PM   #6
hatfieldenator
Feedback Score: 1 reviews
Recipes 
 
Join Date: Sep 2010
Posts: 494
Liked 17 Times on 14 Posts
Likes Given: 3

Default

Here's mine. Its a custom Sabco HLT for my HERMS set up. They welded a half coupler for me for the heating element. I was able to simply drill a hole in the electrical box, insert the heating element, add the gasket it came with, and screw it into the half coupler. It made for a water tight seal without even using teflon. I will probably add high temp silicone in the box as well just to be safe.



__________________
hatfieldenator is offline
3
People Like This 
Reply With Quote Quick reply to this message
Old 12-16-2010, 11:51 PM   #7
trigger
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2010
Location: portland
Posts: 628
Liked 5 Times on 5 Posts
Likes Given: 2

Default

I did exactly what hatfieldenator did, but used a single gang box and soldered a 1" NPS locknut to the keg.

__________________
trigger is offline
 
Reply With Quote Quick reply to this message
Old 12-17-2010, 02:31 PM   #8
Boar Beer
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
Boar Beer's Avatar
Recipes 
 
Join Date: Mar 2008
Location: Central NH, NH
Posts: 575
Liked 16 Times on 13 Posts

Default

Will send photos ASAP

__________________

I was married for 10 years before my wife knew I drank.
Then one day I made a mistake and came home from work sober


Minus33.com

Boar Beer is offline
 
Reply With Quote Quick reply to this message
Old 12-27-2010, 07:01 PM   #9
Yambor44
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
Yambor44's Avatar
Recipes 
 
Join Date: Nov 2008
Location: Ocala Florida
Posts: 1,955
Liked 43 Times on 28 Posts
Likes Given: 6

Default

With the exception of the OP, how do you clean your kettles with those wires permanently affixed?

I am getting ready to convert my system to electric, but want to be able to remove the wire from the pot for cleaning.

__________________
Yambor44 is offline
 
Reply With Quote Quick reply to this message
Old 12-27-2010, 08:48 PM   #10
ScubaSteve
Feedback Score: 0 reviews
 
ScubaSteve's Avatar
Recipes 
 
Join Date: May 2007
Location: New Bern, NC
Posts: 3,691
Liked 68 Times on 50 Posts
Likes Given: 11

Default

I plan on CIP, but my element screws right out and my ground wire can be removed from the lug.

__________________
UNIBREW 5500 SINGLE VESSEL BREWERY
WOODEN SINGLE TIER
ScubaSteve is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
What does your element look like? dboblitt Electric Brewing 4 01-10-2012 04:08 PM
Element Install in a 1/2 Keg LiverDance Electric Brewing 7 12-05-2010 05:36 PM
208 volt element Budzu Electric Brewing 14 11-06-2010 03:19 AM
Where did you get your heating element? CircleC-Brewer Electric Brewing 20 10-29-2010 03:26 PM
Did I just ruin my element? dboblitt Electric Brewing 3 10-11-2010 07:02 PM



Newest Threads

LATEST SPONSOR DEALS