Get your HBT Growlers, Shirts and Membership before the Rush!


Home Brew Forums > Home Brewing Beer > Electric Brewing > Deleting The Hot Liquor Tank
Reply
 
LinkBack Thread Tools
Old 03-02-2013, 02:30 PM   #1
glbrewer
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2013
Posts: 1
Default Deleting The Hot Liquor Tank

I' am building a electric brew system, and was wondering if anybody had any insight into why I could not use a on demand hot water heater instead of building a hot liquor tank. I found a few water heaters that stated they were adjustable +/- 2 degrees F up to 180 degrees F. I was also going to use a RIMS system to control my mash temp. Any comments appreciated.

__________________
glbrewer is offline
 
Reply With Quote Quick reply to this message
Old 03-02-2013, 02:58 PM   #2
microbusbrewery
Senior Member
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
microbusbrewery's Avatar
Recipes 
 
Join Date: Jan 2011
Location: West Jordan, UT
Posts: 1,195
Liked 95 Times on 74 Posts
Likes Given: 47

Default

The temp sounds like it can get you in the range you need. I'd be concerned about the accuracy of the thermostat. Also it's my understanding that the on-demand units won't kick on unless the flow rate meets or exceeds a certain threshold. That could be a problem when you go to sparge if you were planning on fly sparging directly from on-demand unit to mash tun without using a separate vessel to hold the hot water. Plus the on-demand unit will probably cost more than a simple HLT.

__________________
http://www.microbusbrewery.org/
microbusbrewery is offline
 
Reply With Quote Quick reply to this message
Old 03-02-2013, 03:04 PM   #3
AnOldUR
fer-men-TAY-shuhn
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
AnOldUR's Avatar
Recipes 
 
Join Date: Mar 2007
Location: New Jersey
Posts: 6,405
Liked 653 Times on 473 Posts
Likes Given: 486

Default

Suppose it would work if you don't treat your water.

At a minimum I bulk treat my water in the HLT with Campden for chloramines.
__________________
Personal taste is one thing, but to be arrogant about yours is what makes you an a-hole. Don't be an a-hole with personal taste.
. . .This has been a PSA from your local Klubb.

Billy-Klubb
AnOldUR is offline
 
Reply With Quote Quick reply to this message
Old 03-02-2013, 03:23 PM   #4
Bensiff
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
Bensiff's Avatar
Recipes 
 
Join Date: Mar 2008
Location: , Washington, the state
Posts: 4,565
Liked 329 Times on 257 Posts
Likes Given: 53

Default

Some thinking has to go into play, such as whether or not you want to filter the water. The easiest way is to filter the water before it goes into the tankless heater. If that is not a viable option you need to filter afterwards which requires a high temperature housing which would need to be a metal one as the only non-metal I know of is made by Pentek and is good only to 160. Then you need a high temp filter, again, Pentek makes the EPM-10 which is rated to 180 so you would be fine there. I don't have that option as I draw off my household tankless so I drop the setting to 100 degrees to run through my filter and start there. The biggest issue, like microbus said, is you are not going to have very accurate temperature control coming from these things so you would want to set a little low and then circulate through your RIMS to bring up to temp.

__________________
Bensiff is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
DIY Mash tun/hot liquor tank jasonclick Beginners Beer Brewing Forum 3 03-27-2012 03:04 PM
What is a Hot Liquor Tank/Mash Tun? Marshi General Beer Discussion 3 03-24-2012 05:58 AM
Aluminum Hot Liquor Tank BrewskiBroski Equipment/Sanitation 3 09-25-2010 02:33 AM
My new hot liquor tank mdd134 Equipment/Sanitation 6 12-17-2007 08:12 AM
I need a hot liquor tank eviljafar Equipment/Sanitation 9 11-07-2007 12:41 PM



Newest Threads

LATEST SPONSOR DEALS