Home Brew Forums

Home Brew Forums (http://www.homebrewtalk.com/forum.php)
-   Electric Brewing (http://www.homebrewtalk.com/f170/)
-   -   Can someone check my Diagram? (http://www.homebrewtalk.com/f170/can-someone-check-my-diagram-229578/)

magnj 03-03-2011 09:27 PM

Can someone check my Diagram?
 
Well I took a crack at this, not sure how I did, also don't like electrocution. Would someone mind helping me out here? Don't mind my drawing, I can only do so much with mspaint and a laptop track pad.

Is my understanding of the SPST switches correct? 2 terminals, one in one out? Is there a ground? Should I be switching both Live and Neutral with a DPST?

If I am in fact on track, what gauge wiring do I need inside, 12?
Also this is intended to be run on a 15A GFCI circuit powering a march 809 and a 1500W element in a RIMS tube.

Thanks!

http://farm6.static.flickr.com/5219/...32b81555_b.jpg

P-J 03-03-2011 09:34 PM

Looks good. No need to switch anything but the hot wire on a 120V system.
It is a 15 amp circuit so #14 wire is A-ok.

HTH.

magnj 03-03-2011 09:39 PM

Ok, any tips on the pump/element out and the main power in outlets? Should I just go to HD and get regular old outlets? I see people on here with some fancy looking ones...

Walker 03-03-2011 11:19 PM

Quote:

Originally Posted by magnj (Post 2701538)
Ok, any tips on the pump/element out and the main power in outlets? Should I just go to HD and get regular old outlets? I see people on here with some fancy looking ones...

Regular old outlets will work fine, especially at the loads you are using.

Get an outlet rated for 20A, and you're good to go.

For power into the box, I personally don't use an inlet. I just have a power cord attached permanently to the box.

magnj 03-03-2011 11:19 PM

lol I saw the email alert but was unsure why the site did not reflect the post. 1500W LWD, hoping it will be enough to maintain my temps for 10 gallon batches in a 15 gallon aluminum stock pot.

Walker 03-03-2011 11:22 PM

Quote:

Originally Posted by magnj (Post 2701876)
lol I saw the email alert but was unsure why the site did not reflect the post. 1500W LWD, hoping it will be enough to maintain my temps for 10 gallon batches in a 15 gallon aluminum stock pot.

Yeah, sorry. I had focused on the picture and asked my question before I read the damn text above it. So I deleted the post. :D

I would think that 1500W should be able to maintain a mash temp just fine. You'll probably want to do the big heating with some other source and gets mashed in, but after than, I think the little element can maintain things for you.

magnj 03-03-2011 11:22 PM

Ok, for the in side I want a male outlet, will I find one at a big box outlet? For that matter should I just use regular light switches instead of ordering from digikey? My only issue is my box is only 10inx6x3...kinda tight, somehow have to get a heatsink in there too.

magnj 03-03-2011 11:23 PM

Yea I'll be direct firing the HLT and BK with propane, maybe the MLT with low heat for step mashes but that's rare for me.

Walker 03-03-2011 11:24 PM

and other answers:

Yes, you understand SPST switches. One in, one out, only connected with the switch in on position.

And 12 gauge wiring is fine to use for the wiring.

Walker 03-03-2011 11:30 PM

Quote:

Originally Posted by magnj (Post 2701885)
Ok, for the in side I want a male outlet, will I find one at a big box outlet? For that matter should I just use regular light switches instead of ordering from digikey? My only issue is my box is only 10inx6x3...kinda tight, somehow have to get a heatsink in there too.

I don't recall seeing the recessed male power inlets at Lowe's or HomeDepot.

Regular light switches will work, but they take up a lot of space. For the small number of switches you need, I would just go to RadioShack and get them and save the shipping charges.

Lowe's and HomeDepot will also sell toggle switches. Guess it depends on if you care what the final product looks like. Illuminated switches, while cool looking, don't change the functionality. :D

As for the SSR's heatsink, you don't have to put it inside. In fact, you might want to put it outside the box and have a hole cut so that the SSR can still make contact with it.

But, 10x6x3 isn't going to be too small.

I have a 10x12x5, and only use 10x6x5 of it, and I have a lot more stuff in there than you are planning. One whole half of my panel is empty in case I want to expand later.


All times are GMT. The time now is 12:21 AM.

Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.