The Brew Stand Incredible Giveaway

Homebrew Talk - Beer, Wine, Mead, & Cider Brewing Discussion Forum

Help Support Homebrew Talk - Beer, Wine, Mead, & Cider Brewing Discussion Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Status
Not open for further replies.

TxBrew

Administrator
Staff member
Admin
Joined
Feb 10, 2004
Messages
9,309
Reaction score
2,112
The Brew Stand Incredible Giveaway​


Our friends at Brewers Hardware have offered this Single Tier Brew Stand for one lucky winner!

Giveawat  HBT - BHLogo    brewers stand.png

"The Brew Stand" is a single tier brew stand designed for most 15-20 gallon kettles 16" in diameter, including 'Keggles'. 7 years in the making, our unique design maximizes airflow around the burners while minimizing heat wash up the fronts of the kettles, keeping the front of the system as cool as possible. The back of each burner bay is open to allow the exhaust gases to escape out the back. The burner mount heat shield is flush with the bottom of the deck, but open in the back, directing most of the heat rearward. The burner mount heat shields are the same ones we sell and designed to mount out BURN10 10" banjo style burner or a Bayou BJ14.

Giveaway HBT June - brewing stand  BH5418.jpg
Starting from the top, the deck of the stand is constructed of 2" square 16 guage 304 stainless. The deck is supported by 2" diameter .065" wall round tubing legs to fully support kettles to 20 gallon. All of the lateral structural supports are 1.5" .065 wall round tubing. The advantage of the round tubing is we can make most of the welds in our rotary welding lathe, providing a single continuous weld with only one start/stop, providing a single consistent and nearly invisible weld at those points. All of the material cuts are made on a high-end Doringer cold saw, allowing for nearly perfect weld-ready cuts free of discoloration and contamination of an abrasive cut-off saw. (Going off on a tangent: cold saws are really cool! If you've never seen one, they're like a wood miter saw but only turn 54 RPM. The material is clamped in a vise while the 14" fine-toothed blade is flooded with coolant while it cuts, essentially milling through the material without heating it. ) After welding, all of the welds are cleaned and repassivated with an electro-chemical weld cleaner.
The Brew Stand includes the stand itself, burner mount/heat shields, 2 pump mounts (very cool, they clamp in place on the 1.5" tubing, allowing you to adjust their position to align to your kettles.) and Total Locking casters that lock on both roll and rotation.
Front view of the stand

giveaway hbt - june BH5418Front.jpg

The Pump Mount

Giveaway HBT - brewstand BH5418PumpMount.jpg

The Weld Detail

giveaway hbt - brewstand BH5418WeldDetail.jpg

The Leg Detail

giveaway hbt - june BH5418LegDetail.jpg


Rules & Entry

- To enter, reply to this thread one time.

- Forum entry limited to Supporting Members only.

- Shipping to be paid by winner if outside of the contiguous United States.

On June26th we will close this giveaway, put all the names in a box, and draw a winner on June 27th.

Thanks to Brewers Hardware for this awesome donation!

The winner will have 24 hours from the time the winner is posted to claim their prize. If you do not respond with your address within that time a new winner will be chosen. The same rules apply to the next winner.

Giveawat  HBT - BHLogo    brewers stand.png


No purchase necessary. To enter by mail send full name, address, phone number to Entries must be received by June 26th, 2014. Void where prohibited.
 
Last edited by a moderator:
Time to enter! You only have three weeks, so don't delay!
 
Status
Not open for further replies.
Back
Top