Home Brew Forums

Home Brew Forums (http://www.homebrewtalk.com/forum.php)
-   General Beer Discussion (http://www.homebrewtalk.com/f14/)
-   -   Best way to use Temp Control probe (http://www.homebrewtalk.com/f14/best-way-use-temp-control-probe-348149/)

LarryC 08-17-2012 03:07 AM

Best way to use Temp Control probe
 
I just finished wiring up my shiney new Ranco single stage temp controller. I am going to be using it to run a FermWrap around my Better Bottle placed inside of a temp controlled freezer. I've modified the freezer's factory temp control switch to the point where it will hold 40 pretty well but that means it's going to be mighty chilly in there. I was thinking I would tape the Ranco probe to the side of the Better Bottle where the FermWrap has a open space.

That seemed like a good idea until I did a simple test with a glass of water. This is sort of backwards but I was in the garage which was 84 and I filled a glass with water and taped the probe to the glass. I then tossed in a few cubes and waited for the temperature to drop and my Ranco to kick on. The surprising part was that the water in the glass was in the high forties but the temp probe never showed it getting below 67 (waited maybe 10 minutes). One thing to clarify, the glass wasn't real glass - it is one of those acrylic things about 1/8" thick.

So my question is, will taping the probe to the better bottle control the temperature as close as I'd like to be or do I have to get the probe into the fermenting wert?

And the experts say?

eobie 08-17-2012 06:08 PM

In the wort is always the best.

kuphish 08-17-2012 07:52 PM

Did you insulate the probe, or was it just taped against the glass container?

Also, I'm confused. Is your plan to have the freezer running at 40F while the FermWrap keeps the beer at fermentation temperature?

aubiecat 08-17-2012 08:00 PM

Quote:

Originally Posted by eobie (Post 4339262)
In the wort is always the best.

^^This^^

LarryC 08-18-2012 02:18 AM

Quote:

Originally Posted by kuphish (Post 4339616)
Did you insulate the probe, or was it just taped against the glass container?

Also, I'm confused. Is your plan to have the freezer running at 40F while the FermWrap keeps the beer at fermentation temperature?

Yes, that's the plan. I'm converting my old chest freezer to a Keezer slowly but surely. The freezer will sit at about 40 F now with it's factory thermostat and the Ranco will be used to keep a FermWrap on the Better Bottle running so the fermentation temp stays around 65ish (depending on the recipe).

At some point I will probably set up a controller for the freezer temp to bring it up a little but for now, this is what I have.

LarryC 08-18-2012 02:19 AM

Quote:

Originally Posted by eobie (Post 4339262)
In the wort is always the best.

I wasn't sure if the probe was "wert" proof. It will be OK to just sanitize and drop it into the wert?

cwi 08-29-2012 09:29 PM

As suggested earlier, you need to insulate over the top of the taped probe for the 'probe on wall' strategy to work. It is the best possible location when using a controller to directly control a freezer/fridge when used as a ferm chamber. It works even better than a thermowell in the middle of the ferm vessel.

Your application is a little different, so I would guess you would need to add a bunch (3-4") of insulation for it to work even reasonably well. For your current approach, a thermowell placed near the vessel wall would be a better location, . This is what is meant by "in the wort". You cannot just place the probe in your wort, for sanitary reasons; or in a jug of water, for sensor non-waterproofyness reasons.

Even better, though, would be to just plug your keezer into the controller you do have, and tape its probe to the vessel wall, then insulate. Now your controller is controlling the temp of the ferm. Simpler, less energy, better temp control: win-win, win.

Of course, your keezer would not be suitable for much else while ferming, but that is the nature of trying to control ferm temps accurately. There are some guys who try to control multiple ferms using a single cold chamber and multiple heat wraps, but you really need to know what you are doing.

Getting a cheap/free fridge/freezer and a $25 ebay aquarium controller is a much simpler method, provided you have the room. Get another one of these controllers for your keezer, and you won't have to dismantle your thermostat every time you want to adjust your temps. A search on HBT will produce a link to a lengthy thread on them, but most of the information you need is in the first post. They have proven very reliable, with not a single confirmed failure reported to date. Just make sure you get a 110V version of the true STC-1000 controller.

A word of warning: your Ranco controller almost certainly does not have ASD to protect your compressor. You need to be very aware of this shortcoming, or it could cost you your compressor if used for a fridge/freezer. The information is available with a simple search.

BetterSense 08-29-2012 09:49 PM

I want to do exactly this thing, but not because I can't increase my keezer temps. I want to do it so that I can ferment ales in my keezer, and still leave my kegs at serving temperature, all in the same keezer. I think if I use a fermwrap around my carboy, it might work, but I don't know if a thermowell will be necessary.

terrapinj 08-29-2012 10:03 PM

won't the fermwrap give off heat and impact the ambient temp inside the freezer?

kuphish 08-29-2012 11:21 PM

Quote:

Originally Posted by cwi (Post 4371894)
Even better, though, would be to just plug your keezer into the controller you do have, and tape its probe to the vessel wall, then insulate. Now your controller is controlling the temp of the ferm. Simpler, less energy, better temp control: win-win, win.

I totally forgot about this thread. Glad I looked back. Your quoted text is exactly what I would suggest and the reason I posed the question earlier.

To the OP: I'm not sure I understand why you want to have the freezer and fermwrap working against each other. I agree with the quote above. It's much more efficient to just control the temperature of fermentation with the freezer by attaching an insulated probe to your fermentation vessel.

Good luck!

:mug:


All times are GMT. The time now is 05:25 PM.

Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.