Ss Brewing Technologies Giveaway!

Home Brew Forums > Home Brewing Beer > Brew Science > Ph after RO treatment
Reply
 
LinkBack Thread Tools
Old 04-02-2012, 09:59 AM   #1
Ben58
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
Ben58's Avatar
Recipes 
 
Join Date: Aug 2011
Location: Hamilton, Ontario
Posts: 239
Liked 11 Times on 7 Posts
Likes Given: 24

Default Ph after RO treatment

Calibrated my meter and checked the Ph of my RO water. 8.42, meter is a Hannah pHep5. Does this seem right?

__________________
Ben58 is offline
 
Reply With Quote Quick reply to this message
Old 04-02-2012, 11:35 AM   #2
ajdelange
Senior Member
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2010
Location: McLean/Ogden, Virginia/Quebec
Posts: 5,934
Liked 587 Times on 485 Posts
Likes Given: 16

Default

No, that doesn't seem right or not usual anyway but if the meter reads 4 in 4 buffer and 7 in 7 buffer then it could be. RO membranes pass hydrogen ions so there is usually a slight downward shift in pH. Plus permeate is usually low enough in ions that the CO2 it dissolves from air is sufficient to overcome the slight buffering capacity of the water and lower the pH. Something around pH 6 might be more typical. OTOH if the feed is at high pH and loaded with alkalinity the permeate could be at higher pH.

What is the feed water like? What's it's pH and alkalinity?

[Edit] I guess I should also add that pH measurement in low ionic strength waters is difficult as pH measurement depends on the completion of an electrical circuit through the water and really pure water is not at all a good conductor. There are special techniques for doing it bight slow response and erratic readings can be expected if they aren't used.

__________________
ajdelange is offline
 
Reply With Quote Quick reply to this message
Old 04-02-2012, 12:41 PM   #3
mabrungard
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2011
Location: Carmel, IN
Posts: 2,714
Liked 184 Times on 161 Posts
Likes Given: 24

Default

Gases pass through RO membranes fairly easily. CO2 is in most water at modest content and is typically the primary concern in large scale RO treatment. We typically include an air-stripping step following the RO membrane to degas the water and reduce the corrosivity of the finished water.

That indicates that a fresh RO sample should have a somewhat low pH. The 8.42 pH would be atypical. Was the pH meter calibrated and was the water confirmed to have a very low Total Dissolved Solids (TDS) content? If neither of those components are confirmed, there isn't much that can be said of the result other than it shouldn't be that high for typical waters.

__________________

Martin B
Carmel, IN
BJCP National
Foam Blowers of Indiana (FBI)

Brewing Water Information at:
https://sites.google.com/site/brunwater/

Like Bru'n Water on Facebook for occasional discussions on brewing water and Bru'n Water

mabrungard is offline
 
Reply With Quote Quick reply to this message
Old 04-02-2012, 11:03 PM   #4
Ben58
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
Ben58's Avatar
Recipes 
 
Join Date: Aug 2011
Location: Hamilton, Ontario
Posts: 239
Liked 11 Times on 7 Posts
Likes Given: 24

Default

My bad. Pooched the calibration. Pre RO is 8.42 and post RO is 6.26. Now to adjust the minerals back, assuming a 90% extraction efficiency of minerals.

__________________
Ben58 is offline
 
Reply With Quote Quick reply to this message
Old 04-03-2012, 03:18 AM   #5
ajdelange
Senior Member
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2010
Location: McLean/Ogden, Virginia/Quebec
Posts: 5,934
Liked 587 Times on 485 Posts
Likes Given: 16

Default

That's more like what we'd expect.

__________________
ajdelange is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Sparge water treatment zrule Brew Science 11 04-04-2012 05:36 PM
Water treatment questions Patirck Brew Science 17 02-28-2011 02:57 PM
Advise on 1st water treatment sco999 Brew Science 5 02-10-2011 06:24 PM
Water treatment question cjsturch Brew Science 6 02-09-2011 07:52 PM
H2O Treatment for Porter recipe CPooley4 Brew Science 10 12-01-2010 12:26 AM