Kegconnection Complete Starter Kit and More Giveaway!


Home Brew Forums > Home Brewing Beer > Brew Science > Beer Efficiency

Reply
 
LinkBack Thread Tools
Old 05-12-2014, 12:03 AM   #1
Tshipp
HBT_SUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2014
Location: Santa Barbara, CA
Posts: 2
Default Beer Efficiency

I have recently graduated to all grain brewing. I have flash and batch sparged a few recipes but I am having trouble getting my efficiency above 55%. The beer taste fine but ferments very quickly. Any help would be appreciated.

__________________
Tshipp is offline
 
Reply With Quote Quick reply to this message
Old 05-12-2014, 02:12 AM   #3
kenmcchord
HBT_SUPPORTER.png
Feedback Score: 1 reviews
 
kenmcchord's Avatar
Recipes 
 
Join Date: Mar 2013
Location: Medford, NJ
Posts: 135
Liked 19 Times on 16 Posts
Likes Given: 63

Default

Quote:
Originally Posted by Yooper View Post
What is your crush like? Do you crush at home, or at the brew store?
+1 on this point.

I recently bought a used barley crusher and last Thursday brewed a Hop Stoopid clone. Best I ever got before was in the low 70's for mash efficiency, usually around 68%. Last Thursday attained 84% efficiency which I am attributing to both the crush and my improved fly sparging technique. I am convinced my grain after being crushed at the LHBS didn't look nearly the same as my crush last week, and the numbers I think prove it.

I don't know what flash sparge means but before I learned how to fly sparge I used to batch sparge. I'm pretty convinced you just can't get the same numbers with batch sparging as you can with fly sparging. That said you should absolutely get into the low 70s with batch sparging, maybe even higher.
I think the crush is a good place to start.
__________________

Check out the Hopvectors Beer Club website

Primary: nothing
Secondary: Red Rye Imperial IPA
Next Brewday: ???

On Tap: Tap #1. Hop Stoopid clone / Tap #2. empty

kenmcchord is offline
 
Reply With Quote Quick reply to this message
Old 05-12-2014, 03:29 AM   #4
helibrewer
HBT_SUPPORTER.png
Feedback Score: 1 reviews
 
helibrewer's Avatar
Recipes 
 
Join Date: Nov 2011
Location: Santa Rosa, CA
Posts: 3,073
Liked 173 Times on 157 Posts
Likes Given: 39

Default

Isolate your efficiency numbers. Figure out your conversion efficiency with this chart: (Enter chart at your grist ratio)



Your SG should 90% or more of the chart SG. If it's not, then you have mash tun issues (crush, pH, temp, etc).

After sparging use this chart for lauter efficiency:



Use this chart by adding water (cold is ok) to your drained MLT using a value from the top of the chart (i.e. 1qt/lb). Take an SG reading. This reading tells you how much fermentable you left in the MLT. Subtract this percentage from your above conversion percentage and you get your Overall Conversion Efficiency.

Using this method you can determine whether your problems are with the mash or the sparge...or both.

__________________
Something is always fermenting....
"It's Bahl Hornin'"

Primary:
Brite Tank/Lagering:
Kegged: Hefeweizen, Chocolate Hazelnut Porter, Kumquat Saison, Tart Cherry Cider, Belgian Tripel, Maibock Bock, Ommegang Abbey Ale Clone, Belgian Golden Strong, German Pils (WLP830)
Bottled: Belgian Quad (Grand Reserve), Derangement (Belgian Dark Strong)
On Deck:
My Site: www.restlesscellars.com
helibrewer is offline
TheRussMeister Likes This 
Reply With Quote Quick reply to this message
Old 05-24-2014, 02:02 AM   #5
harebearva
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2012
Location: Roanoke, va
Posts: 150
Liked 10 Times on 9 Posts
Likes Given: 11

Default

For me, crush made all the difference. I was getting about 70% mash efficiency when I used the LHBS crush. I bought a cheap little Cereal Killer and set it to credit card thickness gap and now I routinely get about 83% using a cooler mash tun and batch sparging.

__________________
harebearva is offline
 
Reply With Quote Quick reply to this message
Old 05-26-2014, 11:01 PM   #6
WoodlandBrew
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
WoodlandBrew's Avatar
Recipes 
 
Join Date: Oct 2012
Location: Malden, MA
Posts: 1,740
Liked 123 Times on 120 Posts
Likes Given: 57

Default

If you can provide your water volumes and grain weight I would be happy to crunch the laughtering numbers for you. Sometimes more grain can actual end up producing less sugar. see here for details:
http://www.woodlandbrew.com/2012/12/...ore-sugar.html

__________________

The 2nd edition is now available: Brewing Engineering
BLOG: Brewing Boiled Down Brewing science for those of us without a Ph.D

WoodlandBrew is offline
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Need help with big beer (1.096) efficiency rockytoptim All Grain & Partial Mash Brewing 6 11-30-2013 09:29 PM
55% Efficiency / Low Beer Volume stewart194 All Grain & Partial Mash Brewing 11 06-04-2013 03:31 PM
bad efficiency = good beer amcclai7 All Grain & Partial Mash Brewing 9 04-24-2012 01:28 PM
Wheat beer efficiency JerD All Grain & Partial Mash Brewing 12 11-11-2009 05:48 PM
Pumpkin beer low efficiency Denny's Evil Concoctions All Grain & Partial Mash Brewing 2 10-09-2006 06:49 AM