Happy HolidaySs Giveaway - Winners Re-Re-Re-Re-Re-Drawn - 24 hours to Claim!

Get your HBT Growlers, Shirts and Membership before the Rush!


Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Electric heating element requirements
Reply
 
LinkBack Thread Tools
Old 12-31-2006, 01:32 AM   #1
FrankC
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2006
Posts: 1
Default Electric heating element requirements

I want to brew 5 gallon all grain batches in my basement. I want to heat with electricity. How powerful do my heating elements need to be? I anticpate using two heating elements: one for heating the sparge water and the other for the boil.

I will appreciate suggestions.

__________________
FrankC is offline
 
Reply With Quote Quick reply to this message
Old 12-31-2006, 09:25 AM   #2
Spoonta
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2005
Location: Western Australia
Posts: 194
Default

try heating elements out of big urns

__________________
"There is nothing more lonesome than a pub with no beer" (slim dusty)


Primary
blonde ale & Belgium Ale
Secondary #1
Empty
Bottled
Corona & Coopers Ginger beer
Kegged
Kolsh & Hopped Pale Ale
Spoonta is offline
 
Reply With Quote Quick reply to this message
Old 12-31-2006, 01:14 PM   #3
DAAB
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2005
Posts: 379
Liked 1 Times on 1 Posts

Default

Although a few homebrewers in the UK use gas, most will use an electric fired boiler (you dont have to worry about boiling outside or the gas runing ou ). 1 x 2.4kw element is sufficient although it takes a while to bring 5 gals to the boil, so i've installed 2 x 2.4kw elements and use both to bring the wort to the boil and switch to one to maintain a rolling boil. If you use anything more powerfull you may find it usefull to install a power controler.

__________________
My 'How to Homebrew Pages'
DAAB is offline
 
Reply With Quote Quick reply to this message
Old 12-31-2006, 03:30 PM   #4
david_42
Feedback Score: 0 reviews
 
david_42's Avatar
Recipes 
 
Join Date: Oct 2005
Location: Willamina & Oak Grove, Oregon, USA
Posts: 25,662
Liked 139 Times on 132 Posts

Default

Try searching on heat sticks.

__________________

Remember one unassailable statistic, as explained by the late, great George Carlin: "Just think of how stupid the average person is, and then realize half of them are even stupider!"

"I would like to die on Mars, just not on impact." Elon Musk

david_42 is offline
 
Reply With Quote Quick reply to this message
Old 12-31-2006, 07:57 PM   #5
barside laundry
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2005
Location: lancaster, pa
Posts: 62
Default

I also brew all grain in my basement with electric. I use a 3.5kw low density element in a keggle. I use a 10 gallon rubbermaid cooler for my hlt with a small heating element in the bottom. I wish I could say I came up with it but I found the idea on www.powersbrewery.com. check it out, that guy has it all figured out and I have modeled my equipment after his and it works great.

__________________
Tap 1 (stout faucet w/ nitrogen): Trout's Oatmeal Stout

Tap 2: none

Primary: Bavarian Dunkel
Secondary: Victory Hop Devil

"That rug really tied the room together, did it not?"
barside laundry is offline
 
Reply With Quote Quick reply to this message
Old 12-31-2006, 08:22 PM   #6
Orfy
For the love of beer!
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
Orfy's Avatar
Recipes 
 
Join Date: Sep 2005
Location: Cheshire, England
Posts: 11,853
Liked 69 Times on 52 Posts
Likes Given: 30

Default

I just use a cheap domestic immersion heater.

__________________
GET THE GOBLIN
Have a beer on me.
Orfy is offline
 
Reply With Quote Quick reply to this message
Old 01-01-2007, 06:19 PM   #7
brewman !
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2006
Posts: 1,228
Liked 14 Times on 13 Posts
Likes Given: 16

Default

You have to watch that you get an element with enough area otherwise it will scorch the wort. And some elements are supposed to be mounted horizontally and not vertically, according to the instructions that come with them.

Quote:
I use a 10 gallon rubbermaid cooler for my hlt with a small heating element in the bottom.
How do you like that setup ? Are you finding the Gott is standing up OK or is it warping ?
__________________

Getting back into brewing...


brewman ! is offline
 
Reply With Quote Quick reply to this message
Old 01-02-2007, 11:59 PM   #8
barside laundry
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2005
Location: lancaster, pa
Posts: 62
Default

I love the setup. the inside white plastic shell has developed waves or indications of warping but that occured the first time or two and since then it has been perfect. I control the element with a Ranco ETC. Scorching is not an issue because i only use this to heat my hot water for sparging. I also use the same kind of cooler for mashing but without a heating element. I find that it loses about 1-2 degrees per hour during a 10lbs 153F mash.

__________________
Tap 1 (stout faucet w/ nitrogen): Trout's Oatmeal Stout

Tap 2: none

Primary: Bavarian Dunkel
Secondary: Victory Hop Devil

"That rug really tied the room together, did it not?"
barside laundry is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
electric heating element Brewpastor Brew Stands 9 01-01-2012 10:20 PM
Going electric, heating element question. jmp138 Kettles, Mash Tuns, & Hot Liquor Tanks 33 02-27-2011 01:16 AM
anyone consider installing an electric heating element to their BK? krausenmustache Kettles, Mash Tuns, & Hot Liquor Tanks 24 05-12-2009 06:29 PM
Electric heating element CircleC-Brewer Equipment/Sanitation 4 08-04-2008 09:26 PM
No-welding electric heating element? RockfordWhite Brew Stands 4 12-27-2007 06:52 AM



Newest Threads

LATEST SPONSOR DEALS