Electric Brewing Supply 30A BCS Giveaway!


Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Brewhemoth conicals?
Reply
 
LinkBack Thread Tools
Old 11-06-2012, 05:39 PM   #761
Shockerengr
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2007
Posts: 441
Liked 20 Times on 17 Posts
Likes Given: 1

Default

Quote:
Originally Posted by CharlosCarlies View Post
I'm sure this has already been addressed, but since the thread has gotten so big:

Where are you guys racking into? I was originally just going to pump up into the racking port, but then got to wondering if going through the 1" TC in the top might be better to get some additional splashing/aeration action going on.

Thoughts?

I pump the wort in through the top to help with the aeration.
__________________
Shockerengr is offline
 
Reply With Quote Quick reply to this message
Old 11-06-2012, 05:43 PM   #762
Shockerengr
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2007
Posts: 441
Liked 20 Times on 17 Posts
Likes Given: 1

Default

Quote:
Originally Posted by fork View Post
You say seal, but you wouldn't want to completely seal a tank with boiling or even very hot water in it. When it cools it would create a vacuum and tanks like these can't handle a vacuum. I've seen the result of imploding tanks at commercial breweries and it isn't pretty.
Very valid point, and you're right, there should be vacuum relief if using boiling water.

That said, just hot or boiling water being added wouldn't be enough by itself. If there is air inside when sealed, you won't get the vacuum after it cooled as you do when boiling water drives all the air out and replaces it with water vapor.

At the same time, if you're not driving all the air out and boiling, you probably aren't getting good sanitation.

Even with all that, the brewhemoth might still be strong enough to survive a high negative pressure. The diameter isn't that large, and the steel used is quite thick. That said, I have no intention of testing this theory out with mine
__________________
Shockerengr is offline
 
Reply With Quote Quick reply to this message
Old 11-06-2012, 07:14 PM   #763
CharlosCarlies
Senior Member
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
CharlosCarlies's Avatar
Recipes 
 
Join Date: Jan 2009
Location: Conroe, TX
Posts: 710
Liked 9 Times on 7 Posts

Default

Quote:
Originally Posted by Shockerengr View Post
I pump the wort in through the top to help with the aeration.
Good to hear.
__________________
CharlosCarlies is offline
 
Reply With Quote Quick reply to this message
Old 12-04-2012, 02:54 AM   #764
Jukas
HBT_LIFETIMESUPPORTER.png
Feedback Score: 4 reviews
Recipes 
 
Join Date: Dec 2011
Location: Santa Rosa, CA
Posts: 918
Liked 86 Times on 69 Posts
Likes Given: 23

Default

So I've been conical shopping for at last six months trying to make a decision.. I think I have it narrowed down to either the brewhemoth or a 14.5g short Stout. I'd really prefer the brewhemoth and went to impulsively order one last week but their site had issues so I forced myself to low down and rethink. I read this entire thread over the last 24hrs but theres some things I never saw a clear answer to.

A) Temp differential capability of the IC when used with a pump & freezer/glycol mix? It's not uncommon for my garage to hit 100F in the summer and I'm dubious that short of a glycol power pack I'd be able to hit lager/cold crash temps.

B) Are there any Fridges or Freezers that will fit this? With above in mind, I'd normally vote to just skip the IC and get a fridge or freezer, but this thing is huge compared to others, and nothing I've seen can easily fit 19"w by 56" high (website says 50" I'm figuring the other 6" for the spunding valve & general clearance). Some of the commercial ones might, but they're harder to find on CL in my neighborhood and almost the cost of a glycol power pack to boot.

C) I believe most commercial breweries sanitize with steam, has anyone devised a way to do so with the hemoth?

__________________
Jukas is offline
 
Reply With Quote Quick reply to this message
Old 12-04-2012, 09:07 PM   #765
DaleP
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2010
Location: Webster Groves, Missouri
Posts: 144
Liked 9 Times on 9 Posts
Likes Given: 7

Default

B) Is an easy one, there are many folks who have their Brewhemoth in a fridge, The legs are adjustable.
A) If you put an insulating blanket on the Brewhemoth, temps 47-50 should be attainable, especially with 28 degree glycol. In a 100 degree room, getting it down in the low 30's, not sure, never tried it, always lagered my beers in kegs, in freezers, hated tying up fermenter space.
Hope I helped.

__________________
DaleP is offline
 
Reply With Quote Quick reply to this message
Old 12-05-2012, 06:21 PM   #766
Jukas
HBT_LIFETIMESUPPORTER.png
Feedback Score: 4 reviews
Recipes 
 
Join Date: Dec 2011
Location: Santa Rosa, CA
Posts: 918
Liked 86 Times on 69 Posts
Likes Given: 23

Default

Quote:
Originally Posted by DaleP View Post
B) Is an easy one, there are many folks who have their Brewhemoth in a fridge, The legs are adjustable.
A) If you put an insulating blanket on the Brewhemoth, temps 47-50 should be attainable, especially with 28 degree glycol. In a 100 degree room, getting it down in the low 30's, not sure, never tried it, always lagered my beers in kegs, in freezers, hated tying up fermenter space.
Hope I helped.

Dale,

Cheers for the reply. Since the legs are adjustable, can you give me an idea of the minimum height requirement for the hemoth with the spunding valve attached (http://brewhemoth.com/spunding-valve) and a 90deg bend on the dump valve?
__________________
Jukas is offline
 
Reply With Quote Quick reply to this message
Old 12-05-2012, 07:26 PM   #767
blad3rR
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2010
Location: Berkeley, CA
Posts: 42
Likes Given: 5

Default

Jukas,

Blackheart brewing has these in some sort of fridge/freezer

http://downthepieratehole.wordpress....ors-un-boxing/

__________________
blad3rR is offline
 
Reply With Quote Quick reply to this message
Old 12-07-2012, 09:36 AM   #768
DaleP
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2010
Location: Webster Groves, Missouri
Posts: 144
Liked 9 Times on 9 Posts
Likes Given: 7

Default

With the spunding valve on top, you are in the neighborhood of 36 inches. I'm not sure how tall the 90 is, I'll look into this at work today.

__________________
DaleP is offline
 
Reply With Quote Quick reply to this message
Old 01-09-2013, 07:17 PM   #769
Danzaslapped
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2012
Location: New York, New York
Posts: 3
Likes Given: 1

Default Tri Clover Brewhemoth

Waiting on the delivery of my Tri Clover Brewhemoth (w/ spunding valve & immersion coil) Patiently. But in the mean time I'm trying to get a parts list together of what I need to order to get this 100% working once its delivered. I'm clueless in the engineering department and need to have this fully planned out for my Breweries new pilot system (Or else they'll go with Morebeer, please no). Ordered an extra 4" cap so I can have a spray ball attachable to a 1/2" nipple welded into it. Also had an extra tri coupler installed for the racking arm.

Does this part list look all encompassing?

https://docs.google.com/spreadsheet/...VBHdmhlNXdSZUE

Anything wrong/what else do I need?

__________________
Danzaslapped is offline
 
Reply With Quote Quick reply to this message
Old 01-10-2013, 12:30 AM   #770
Jukas
HBT_LIFETIMESUPPORTER.png
Feedback Score: 4 reviews
Recipes 
 
Join Date: Dec 2011
Location: Santa Rosa, CA
Posts: 918
Liked 86 Times on 69 Posts
Likes Given: 23

Default

I too am waiting on my tri clover hemoth with spunding valve and IC. Here's the fittings I was looking at, though I am having second thoughts about hte squeeze trigger butterfly valve vs the normal butterfly valves.

(1) 1/1.5 TC to 1/2" hose barb 90 deg bend. $15
(1) 1/1.5" TC Clamp $6
(1) 1" EPDM Sanitary Gasket $1.25

Racking Valves
(1) 1/1.5" Sampling Valve $29
(1) 1" Tri Clover Squeeze Trigger butterfly valve $49
(2) 1/1.5" TC Clamp $12
(2) 1" EPDM Sanitary Gasket $2.50

Thermowell

(1) 1/1.5" Tri Clover Thermowell 12" $24
(1) 1/1.5" TC Clamp $6


Dump Valves
(1) 1.5" Squeeze Trigger Butterfly Valve $53
(2) 1/1.5" TC Clamp $12
(2) 1.5" EPDM Sanitary Gasket $2.50
(1) 1/1.5" TC Cap $3

Misc:
(2) 1/1.5" TC Cap. $6
(6) 1" EPDM Sanitary Gasket $7.50
(6) 1.5" EPDM Sanitary Gasket $7.50
(2) 1/1.5" TC Clamp $12

Total: $248.25

__________________
Jukas is offline
Danzaslapped Likes This 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
MoreBeer Conicals zymurgy101 Equipment/Sanitation 13 07-04-2011 05:49 PM
Chinese conicals Styles Equipment/Sanitation 23 09-28-2009 01:49 AM
Usage of conicals billtzk Equipment/Sanitation 19 11-27-2008 02:25 AM
Conicals Kayos Equipment/Sanitation 10 02-07-2008 07:31 PM
Using conicals- MikeFlynn74 Equipment/Sanitation 6 12-01-2007 10:36 AM