Ss Brewing Technologies Giveaway!

Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Beveragefactory.com draft beer tower
Reply
 
LinkBack Thread Tools
Old 01-29-2013, 05:02 PM   #1
m_c_zero
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2011
Location: Fort Collins, CO
Posts: 747
Liked 122 Times on 94 Posts
Likes Given: 188

Default Beveragefactory.com draft beer tower

Purchased a 2 tap draft beer tower from beveragefactory.com and had both of the factory beer lines end up having leaks. Not sure if I just got some bad hoses or what, but just a word of caution, I would recommend replacing the hoses right away.

EDIT: Discovered it was not the beer lines that were leaking. Issue was a leaky elbow shank. See last post.

__________________
m_c_zero is online now
 
Reply With Quote Quick reply to this message
Old 01-29-2013, 05:21 PM   #2
FermentNEthinG
Mash Tun Warrior
HBT_SUPPORTER.png
Feedback Score: 9 reviews
 
FermentNEthinG's Avatar
Recipes 
 
Join Date: Sep 2012
Location: Homebrew Haven, NY
Posts: 1,153
Liked 1005 Times on 513 Posts
Likes Given: 2319

Default

Where did the leak originate from? The faucet barbs?

__________________
FermentNEthinG is offline
 
Reply With Quote Quick reply to this message
Old 01-29-2013, 08:04 PM   #3
m_c_zero
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2011
Location: Fort Collins, CO
Posts: 747
Liked 122 Times on 94 Posts
Likes Given: 188

Default

Quote:
Originally Posted by FermentNEthinG View Post
Where did the leak originate from? The faucet barbs?
Not sure, but I believe so.
__________________
m_c_zero is online now
 
Reply With Quote Quick reply to this message
Old 01-29-2013, 08:07 PM   #4
weirdboy
HBT_LIFETIMESUPPORTER.png
Feedback Score: 4 reviews
Recipes 
 
Join Date: May 2009
Location: Los Angeles
Posts: 7,972
Liked 431 Times on 352 Posts
Likes Given: 60

Default

I dunno, I got a 3-tap tower from them and didn't have any trouble except one of the shank nuts was on there so tight I stripped it trying to get it off, and they sent me a new one.


Of course, it's been a very long time since I have had the original hoses on there, but I don't remember any leaks.

__________________
weirdboy is offline
 
Reply With Quote Quick reply to this message
Old 01-29-2013, 08:21 PM   #5
mikronmagic
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2012
Location: GAINESVILLE, FL - Florida
Posts: 28
Likes Given: 2

Default

I've ordered 4 towers from them and only had one issue (perlick faucet wasn't cast perfectly and required some filing to make it not seat correctly - not really their fault).
Sounds like you got really unlucky!

__________________
mikronmagic is offline
 
Reply With Quote Quick reply to this message
Old 01-29-2013, 09:37 PM   #6
m_c_zero
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2011
Location: Fort Collins, CO
Posts: 747
Liked 122 Times on 94 Posts
Likes Given: 188

Default

Quote:
Originally Posted by mikronmagic View Post
Sounds like you got really unlucky!
Yeah, could be. Funny thing is that they both leaked at different times. One leaked right away and the other one took a couple months before it leaked.
__________________
m_c_zero is online now
 
Reply With Quote Quick reply to this message
Old 01-30-2013, 01:16 AM   #7
brettg20
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2009
Location: Newport Beach, CA
Posts: 691
Liked 83 Times on 59 Posts
Likes Given: 7

Default

I purchased 4 double towers over 2 years ago and have never had a problem.

__________________
brettg20 is offline
 
Reply With Quote Quick reply to this message
Old 02-14-2013, 06:19 PM   #8
m_c_zero
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2011
Location: Fort Collins, CO
Posts: 747
Liked 122 Times on 94 Posts
Likes Given: 188

Default

Finally found out the problem. It wasn't the lines at all. Turns out it was a leaky elbow shank. Seems there is a pinhole leak where the elbow is soldered into the shank.

Contacted their support department this morning via e-mail, a few hours later got an e-mail back stating that they had placed an order to send me out a replacement at no cost and I don't even need to send the leaky one back. Very satisfied with their customer service.

__________________
m_c_zero is online now
 
Reply With Quote Quick reply to this message
Old 02-15-2013, 08:11 PM   #9
daksin
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
daksin's Avatar
Recipes 
 
Join Date: Aug 2011
Location: San Diego, CA
Posts: 4,098
Liked 272 Times on 238 Posts
Likes Given: 324

Default

Quote:
Originally Posted by m_c_zero View Post
Finally found out the problem. It wasn't the lines at all. Turns out it was a leaky elbow shank. Seems there is a pinhole leak where the elbow is soldered into the shank.

Contacted their support department this morning via e-mail, a few hours later got an e-mail back stating that they had placed an order to send me out a replacement at no cost and I don't even need to send the leaky one back. Very satisfied with their customer service.
Interested in selling the faulty one? I'll be first in line. Seems like an easy fix.
__________________

I can't be arsed to keep up this list of what's in the fermenters, but hey, check out the cool brewery I own!

twitter.com/2kidsbrewing .. facebook.com/2kidsbrewing .. 2kidsbrewing.com

daksin is offline
 
Reply With Quote Quick reply to this message
Old 03-21-2013, 10:51 PM   #10
EHV
HBT_SUPPORTER.png
Feedback Score: 4 reviews
 
EHV's Avatar
Recipes 
 
Join Date: Jan 2013
Location: , Ohio
Posts: 891
Liked 165 Times on 128 Posts
Likes Given: 61

Default

I'm going to bump this up.
I am dealing with this right now. Unsure where the leak is coming from, but they are sending a new shank I believe. What size wrench (guessing flare nut wrench) did you use. I am going to have to go and buy one. The tolerances are so tight.
I also have the 2 tap tower.

__________________
EHV is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Draft Beer Tower Phoerig Bottling/Kegging 2 11-20-2012 12:10 AM
For Sale - Single Draft beer Tower $50 zman For Sale 4 03-14-2011 07:34 AM
Picking a Draft Beer Tower Illinibrew Bottling/Kegging 14 09-01-2010 01:55 AM
Draft beer tower DIY Vovo Bottling/Kegging 18 02-22-2007 03:41 PM